536907
20
Zoom out
Zoom in
Previous page
1/53
Next page
20-EN
4
Turn the Rotary encoder to adjust the level, and then
press ENTER.
LEVEL: 0 ~ 8
5
Repeat steps 3 to 4 to complete the setting of other bands.
Note
There is no MX mode for FM, MW and LW radio.
You can change the unit, (cm or inch) of time correction.
Setting item: TCR Parameter
Setting contents:
cm (Initial setting) / inch
cm:
Time correction value is in centimetres.
inch:
Time correction value is in inches.
Before performing the following procedures, refer to “About Time
Correction” on page 21.
1
After selecting T.Correction from the Audio Setup mode,
turn the Rotary encoder to select a speaker to be
adjusted, and then press ENTER.
F-L
*1
F-R
*2
R-L
*3
R-R
*4
SW-L SW-R
*1 Front-L
*2 Front -R
*3 Rear-L
*4 Rear-R
2
Turn the Rotary encoder to adjust the distance of the
selected speaker, and then press ENTER.
0.0 cm to 336.6 cm (3.4 cm/step)
0.0 inch to 132.7 inch (1.3 inch/step)
Note
The total adjustment distance for all speakers should be less than 510
centimetres (201 inches).
3
Repeat steps 1 and 2 to set another speaker.
By setting these values to make its sound reach the listening
position at the same time as the sound of other speakers.
This function allows you to change the sound field easily.
There are three modes to choose from. For details, refer to the table
below.
Before performing the following procedures, refer to “About the
Crossover” on page 22.
1
After selecting X-Over from the Audio Setup mode, turn
the Rotary encoder to select the desired channel, and
then press ENTER.
2
Turn the Rotary encoder to select the desired frequency
within the selected channel, and then press ENTER.
3
Repeat step 2 to adjust the slope and Level within the
selected channel.
Adjusting the Channel (Ch.)
Setting contents:
Front (HPF) / Rear (HPF) / SUBW (LPF)
Selecting the Cut-Off Frequency (Freq.)
Setting contents:
20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) / 100 / 125 /
160 / 200 (Hz)
Adjusting the Slope
Setting contents:
Flat (Initial setting) / 6 / 12 / 18 / 24 dB/oct.
Adjusting the Level (Lev.)
Setting contents:
−12 to 0 (dB) (Initial setting: 0)
The Parametric EQ/T.Correction and X-Over settings can be stored in
the preset memory.
1
The Parametric EQ/T.Correction/X-OVER settings can be
stored in any one of the preset buttons(1 through 6).
After completing any adjustment for Parametric EQ/
T.Correction/X-OVER (e.g. Band), press and hold the
desired preset button for at least 2 seconds.
2
Turn the Rotary encoder to select Protect YES/NO, and
then press ENTER to store the adjusted contents.
Protect NO Protect YES (Initial setting)
Notes
If Protect YES is selected, the adjusted contents are protected and stored
into the preset buttons. When you want to store the parameter into a
protected preset button, “Replace NO/YES can be selected.
If Protect NO is selected, the preset is stored.
While perform this operation, all adjusted contents of Parametric EQ/
T.Correction and X-Over will be stored in the preset buttons.
The stored contents are not deleted even when resetting the unit or
disconnecting the battery.
The stored contents can be recalled by performing operation (refer to
“Recalling the Stored Parametric EQ/T.Correction/X-Over Settings” on
page 21).
Setting the Time Correction Unit
(TCR Parameter)
Adjusting the Time Correction
(T.Correction)
Adjusting the SPATIAL
Mode Effect
OFF
(Initial setting)
No effect is applied.
OFF status
Front Wide
Creates the effect of widening the front sound
field by delaying the sound of the front
speakers.
Rear Wide
Creates the effect of making the front sound
image clear and far by delaying the sound of
the rear speakers.
Adjusting the Crossover Settings (X-Over)
Storing the Parametric EQ/T.Correction/
X-Over Settings
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine iDE178BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine iDE178BT in the language / languages: English as an attachment in your email.

The manual is 4,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alpine iDE178BT

Alpine iDE178BT Quick start guide - English, German - 112 pages

Alpine iDE178BT User Manual - German - 58 pages

Alpine iDE178BT Quick start guide - Dutch - 112 pages

Alpine iDE178BT User Manual - Dutch - 58 pages

Alpine iDE178BT Quick start guide - French, Italian, Polish, Swedish, Spanish - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info