168536

Alpine dva 9860 r Manual

35
Zoom out
Zoom in
Previous page
1/64
Next page
34-EN
Setting Bass Compressor
You can adjust the sound of low frequencies as desired.
1
Check that Defeat mode is of f (page 19).
2
Press and hold CENTER f. for at least 2 seconds.
The audio processor control mode is activated.
3
Select the BASS SOUND mode by pr essing
CENTER f. repeatedly .
4
Select BASS COMP . by pr essing g or f.
5
Select the desir ed mode by tur ning and then
pressing the Rotary encoder.
Bass sound is emphasized more as the mode is
sequentially switched as COMP1 → 2 → 3, offering you
vivid low frequencies.
Select OFF when the setting is not necessary.
6
When the setting is complete, pr ess and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press CENTER f. to select another item to be set.
Setting Bass Focus
Using the previously specified delay number (time difference) allows
you to set a time difference between the front-rear/left-right speakers.
Namely, it enables a time correction based on your preference. With
an initial delay of 0.05 ms for each of the 0 to 400 steps, audible time
correction can be achieved.
1
Check that Defeat mode is of f (page 19).
2
Press and hold CENTER f. for at least 2 seconds.
The audio processor control mode is activated.
3
Select the BASS SOUND mode by pr essing
CENTER f. repeatedly .
4
Select BASS FOCUS by pr essing g or f.
5
Press the Rotary encoder to select the fr ont/r ear/
left/right speaker .
6
Set a step of the fr ont (left and right) speaker , and
press the Rotary encoder.
7
When the setting is complete, pr ess and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press CENTER f. to select another item to be set.
• Any setting in Bass Focus is applied in time correction, too.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 37.
Speaker Setup
The PXA-H700 or PXA-H701 can be set according to the playable
frequency range of your speakers.
Check the playable frequency range of the speakers (not including the
subwoofer) before performing this operation to verify whether the
speakers can play low frequencies (of about 80 Hz or less).
•Avoid stopping, pausing, switching the disc, cueing, fast-
forwarding or switching the audio channel of this unit while
making this adjustment. The setting is cancelled if Decode mode is
switched.
1
Check that Defeat mode is of f (page 19).
2
Press and hold CENTER f. for at least 2 seconds.
The audio processor control mode is activated.
3
Select the SP SETUP mode by pr essing
CENTER f. repeatedly .
4
Select the speaker by pr essing the Rotary
encoder.
5
Select the speaker characteristic by tur ning and
then pr essing the Rotary encoder.
OFF*
1
: When no speaker is connected.
SMALL: When a speaker that cannot play low
frequencies (80 Hz or less) is connected.
LARGE*
2
: When a speaker that can play low frequencies
(80 Hz or less) is connected.
*
1
It is not possible to set the front speakers to “OFF”.
*
2
If the front speakers are set to “SMALL”, the rear and
centre speakers cannot be set to “LARGE”.
6
When the setting is complete, pr ess and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press CENTER f. to select another item to be set.
• If the centre speaker is turned “OFF,” the centre channel’s audio
signals are added to the audio signals output from the front
speakers.
• If you set the speaker response to “OFF,” also set the speaker
setting to “OFF.” (page 30)
•Perform the setup for all the speakers (“Front,” “Center,” “Rear”
and “Subwoofer”). If not, the sound may not be balanced.
• When centre is set to “OFF”, the setting is ineffective even if
centre is set with this function.
• Through changing the settings on each speaker, a change in the
output of the other speakers may occur due to the setting
requirements.
• When using the PRO LOGIC II, if the rear speaker is set to
“LARGE”, then there will be no output from the subwoofer.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 37.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine dva 9860 r at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine dva 9860 r in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info