466971
37
Zoom out
Zoom in
Previous page
1/51
Next page
35-EN
Adjusting the Crossover Settings (X-OVER)
Before performing the following procedures, refer to About the
Crossover” (page 38).
2.2ch (3WAY) System
1
After selecting X-OVER from the Sound Field
Adjustment mode, turn the Rotary encoder to
select the band adjustment, and then press
/ENTER.
2.2ch (3WAY) System / NORMAL (L=R)
Setting items:
LOW / MID-L / MID-H / HIGH
2.2ch (3WAY) System / INDIVIDUAL (L/R)
Setting items:
LOW-L / LOW-R / MID-L-L / MID-L-R / MID-H-L /
MID-H-R / HIGH-L / HIGH-R
2
Turn the Rotary encoder to select an item to
adjust, then press
/ENTER.
Cut-off frequency
3
-1 Turn the Rotary encoder to select the desired cut-
off frequency (Crossover Point).
Adjustable frequency bands:
2.2ch (3WAY) System
Setting items:
LOW / MID-L 20 Hz~200 Hz
MID-H 20 Hz~20 kHz
HIGH (1 kHz~20 kHz)*
1
/(20 Hz~20 kHz)*
2
*
1
When FACTORY’S is selected, refer to “Setting the Response Slope
for the High Range Speaker (TW Setup)” (page 36).
*
2
When USER’S is selected, refer to “Setting the Response Slope for
the High Range Speaker (TW Setup)” (page 36).
Level Adjustment
3
-2 Turn the Rotary encoder to adjust the output level.
Adjustable output level: –12 to 0 dB.
Slope Adjustment
3
-3 Turn the Rotary encoder to adjust the slope.
Adjustable slope: FLAT*, 6 dB/oct., 12 dB/oct., 18 dB/oct.,
24 dB/oct.
* FLAT can be set for the HIGH slope only when USER’S is selected in
“Setting the Response Slope for the High Range Speaker (TW
Setup)” (page 36). Depending on the response characteristics of the
speaker, care should be taken when setting the response slope to
FLAT, as speaker damage may result. With this unit, a message is
displayed when the response slope for the high range speaker is set
to FLAT.
4
Repeat steps 1 to 3 to make adjustment to the other
bands.
4.2ch (FRONT/REAR/SUBW.) System
1
After selecting X-OVER from the Sound Field
Adjustment mode, turn the Rotary encoder to
select the band adjustment, and then press
/ENTER.
4.2ch (FRONT/REAR/SUBW.) System / NORMAL (L=R)
Setting items:
LOW (SUB-W) / MID (REAR) / HIGH (FRONT)
4.2ch (FRONT/REAR/SUBW.) System / INDIVIDUAL (L/R)
Setting items:
LOW (SUB-W)-L / LOW (SUB-W)-R / MID (REAR)-L /
MID (REAR)-R / HIGH (FRONT)-L / HIGH (FRONT)-R
2
Turn the Rotary encoder to select an item to
adjust, then press
/ENTER.
Cut-off frequency
3
-1
Turn the
Rotary encoder
to select the desired cut-
off
frequency (Crossover Point).
Adjustable frequency bands:
4.2ch (FRONT/REAR/SUBW.) System
Setting items:
20 Hz~200 Hz
Level Adjustment
3
-2 Turn the Rotary encoder to adjust the output level.
Adjustable output level: -12 to 0 dB.
Slope Adjustment
3
-3 Turn the Rotary encoder to adjust the slope.
Adjustable slope: FLAT, 6 dB/oct., 12 dB/oct., 18 dB/oct.,
24 dB/oct.
4
Repeat steps 1 to 3 to make adjustment to the other
bands.
While adjusting the X-over, you should consider the frequency
response of the connected speakers.
About the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system
You can switch to 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.)
system mode with the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.)
switch on the PXA-H100. For details, refer to the Owner’s Manual of
PXA-H100.
FC
LV SLP FC
(cut-off (level) (slope) (frequency)
frequency)
FC
LV SLP FC
(cut-off (level) (slope) (frequency)
frequency)
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine CDA-118M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine CDA-118M in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 3,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info