Manual Alpina TR 250 J (page 15 of 24) (All languages)

731989

Zoom out

Zoom in

1/24

or by gripping the handgrips excessively

tightly. If the symptoms occur, the length of

time the machine is used must be reduced

and a doctor consulted.

DANGER! This machine’s starter

unit generates an average sized electromag-

netic eld, but it is not however possible to

exclude the possibility of interference on any

active or passive medical devices that opera-

tors may be wearing; this could be risky for

their health conditions. All those using med-

ical devices should always consult their GP,

or the device manufacturer, before using this

machine.

WARNING! Always wear suitable clo-

thing when using the machine. Your dealer

can provide you with all the information on

the most suitable accident-prevention de-

vices to guarantee your safety.

To respect people and the environment:

– Try not to cause any disturbance.

– Scrupulously comply with local regulations

and provisions for the disposal of waste

materials after sawing.

– Scrupulously comply with local regulations

and provisions for the disposal of oils, pet-

rol, damaged parts or any elements which

have a strong impact on the environment.

WARNING! Prolonged exposure to vi-

brations can cause injuries and neurovascular

disorders (also called “Renaud’s syndrome”

or “white hand”), especially to people suer-

ing from circulation disorders. The symptoms

can regard the hands, wrists and ngers and

are shown through loss of sensitivity, torpor,

itching, pain and discolouring of or structural

changes to the skin. These eects can be

worsened by low ambient temperatures and/

The movement is transmitted from the engine to

the drive shaft by a centrifugal mass clutch that

prevents the shaft from moving when the engine

is running at minimum speed.

WARNING! Do not use the machine if

the cutting device moves when the engine is

running idle; in this case, contact you dealer.

The correct running speed will be achieved by

pressing the throttle trigger (2) as far as possible.

IMPORTANT Avoid using the engine at full

power for the rst 6-8 working hours.

STOPPING THE ENGINE (Fig. 5)

To stop the engine:

– Release the throttle trigger (2) and allow the

engine to run idle for a few seconds.

– Set the switch (1) to «STOP».

WARNING! When you have reduced

speed to a minimum, it will take a few sec-

onds for the cutting device to stop.

9. Disconnect the shutter (7 - if provided) briey

activating the throttle trigger (2), to take the

engine back to minimum speed.

10. Let the engine run idle for at least 1 minute

before using the machine.

IMPORTANT If the starter rope is pulled

repeatedly with the choke on, it may ood the en-

gine and make starting dicult.

If you have ooded the engine, remove the spark

plug and gently pull the handle on the starter rope

to eliminate any excess fuel; then dry the spark

plug electrodes and replace it on the en gine.

• Hot starting

When hot starting (immediately after stopping the

engine), follow the procedure indicated above in

points 1 - 5 - 6 - 7.

USE OF THE ENGINE (Fig. 5)

Cutting device speed is regulated by the throttle

trigger (2), located on the rear handgrip (4) or the

right handgrip (4a) of the handlebar.

The throttle trigger only works if the lockout (3) is

pressed at the same time.

HOW TO START - USE - STOP THE ENGINE / USING THE MACHINE

7. USING THE MACHINE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina TR 250 J in the language / languages: All languages as an attachment in your email.

The manual is 1,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina TR 250 J Manual

Product: