731980

Alpina TB 250 JD Manual

12
Zoom out
Zoom in
Previous page
1/28
Next page
6
EN
IMPORTANT
The machine is supplied
with some of the components disassembled and
the fuel tank empty.
WARNING!
Always wear strong work
gloves to handle the cutting devices. Mount
the components very carefully so as not to
impair the safety and eciency of the ma
chine. If in doubt, contact your dealer.
1. COMPLETING THE MACHINE
1a. “MONO” models (Fig. 1)
– Fit the sleeve (2) and the lower part (3) with
guard, placing the pin (3a) in one of the three
holes on the drive tube.
– Fit the front handgrip (4) by using the screws (5).
– Before tightening the screws (4), align the hand-
grip correctly with respect to the drive tube.
– Fully tighten the screws (4).
1b. “DUPLEX” models (Fig. 2)
– Unscrew the central knob (1) and remove the
cap (2), taking care not to separate the two parts
of the handle bar support (3) and (4) so as not to
cause the release of the spring (5) from its seat.
– Insert the handle bar (6), making sure that the
controls are on the right.
– Set the handle bar in the working position and
lock it using the cap (2) and knob (1).
– Fasten the casing (7) of the controls to its cable
fastener (8).
NOTE
By loosening the knob (1),
you can turn the handle bar 90° to reduce its size
for storage.
2. MOUNTING THE ROD
(Models with separate rod – Fig. 3)
– Pull out the stop pin (1) and push the lower part
of the rod (2) right down until the stop pin (1)
slots into the hole (3) in the rod. This is easier to
do if you rotate the bottom of the rod (2) slightly
in both directions. The pin (1) is in place when
it is completely lodged in the hole.
– Lastly, tighten the knob (4) securely.
3. FITTING THE GUARDS
WARNING!
Each cutting device is
pro vided with a specic guard. Never use
guards other than those indicated for each
cutting device.
• 3 point blade (Fig. 4)
WARNING!
Wear protective gloves
and t the blade guard.
– Loosen the screws (1) and remove the plate (2)
from the guard (3).
– Position the guard (3) in correspondence with
the end of the drive tube (4) and apply the plate
(2) fastening it with screws (1), without tighten-
ing them, so that the guard is free to slide on
the tube.
– Set the guard (3) by bringing the central screw
(5) in correspondence with the hole (6) located
on the drive tube and fully tightening it so that
it remains completely inserted in the hole, pre-
venting the movement of the guard.
– Fully tighten the screws (1).
• Cutting line head (Fig. 5)
WARNING!
When using the cutting
line head the additional guard, with line cut-
ting knife, must always be tted.
– Loosen the screws (1) and remove the plate (2)
from the guard (3).
– Position the guard (3) in correspondence with
the end of the drive tube (4) and apply the plate
(2) fastening it with screws (1), without tighten-
ing them, so that the guard is free to slide on
the tube.
– Set the guard (3) by bringing the central screw
(5) in correspondence with the hole (6) located
on the drive tube and fully tightening it so that
it remains completely inserted in the hole, pre-
venting the movement of the guard.
– Fully tighten the screws (1).
– Secure the additional guard (7) using the screw
(8).
4. REMOVING AND REFITTING
THE CUTTING DEVICES
WARNING!
Use only original cutting
devices or ones homologated by the Ma nu-
facturer.
• 3 point blade (Fig. 6)
WARNING!
Wear protective gloves
and t the blade guard.
MACHINE ASSEMBLY
4. MACHINE ASSEMBLY
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpina TB 250 JD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpina TB 250 JD in the language / languages: All languages as an attachment in your email.

The manual is 1,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info