Manual Alpina TB 250 JD (page 11 of 28) (All languages)

731980

Zoom out

Zoom in

1/28

en closure.

4) To reduce re hazards, keep the engine, ex haust

silencer and fuel storage area free from saw dust,

branches, leaves, or excessive grease; ne ver leave

containers with the cut debris inside the storage

area.

5) If the fuel tank has to be emptied, this should be

done outdoors once the engine has cooled down.

6) Always wear protective gloves when handling

the cutting device.

7) For safety reasons, never use the machine

with worn or damaged parts. Damaged parts

are to be replaced and never repaired. Only

use original spare parts. Parts that are not of the

same quality can seriously damage the equipment

and compromise safety. The cutting tools must al-

ways bear the manufacturer’s trademark as well as

a reference to the maximum working speed.

8) Before putting the machine away, check you

have removed wrenches or tools used for main-

tenance.

9) Store the machine out of the reach of children!

E) TRANSPORTATION AND HANDLING

1) Whenever the machine is to be handled or trans-

ported you must:

– turn o the engine, wait for the cutting device to

stop and disconnect the spark plug cap;

– t the cutting device guard;

– only hold the machine using the handgrips and

position the cutting device in the opposite direc-

tion to that used during operation.

2) When using a vehicle to transport the machine,

position it so that it can cause no danger to persons

and fasten it rmly in place to avoid it from tip ping

over, which may cause damage or fuel spil lage.

F) HOW TO READ THE MANUAL

Certain paragraphs in the manual contain particu-

larly signicant information and are marked with

various levels of highlighting with the following

meaning:

NOTE

IMPORTANT

These give details or fur-

ther information on what has already been

said, in the aim to prevent damage to the ma-

chine.

WARNING!

Non-observance will re sult

in the risk of injury to oneself or others.

DANGER!

Non-observance will re sult

in the risk of serious injury or death to one self

or others.

2) Mow only in daylight or good articial light.

3) Take on a rm and well-balanced position:

– where possible, avoid working on wet, slippery

ground or in any case on uneven or steep ground

that does not guarantee stability for the operator;

– never run, but walk carefully paying attention to

the lay of the land and any eventual obstacles;

– assess the potential risks of the ground to be

mown and take all necessary precautions to en-

sure your own safety, especially on slopes or on

bumpy, slippery or unstable ground;

– work along the contour on slopes, never when

walking up or down and always keep downhill

of the cutter.

4) Make sure the machine is securely locked when

you start the engine:

– start the motor in an area at least 3 metres from

where you refuelled;

– check that there is nobody within at least 15 me-

tres of the machine’s range of action or at least 30

metres for heavier mowing;

– do not direct the silencer and therefore the ex-

haust fumes towards inammable materials.

5) Do not change the engine governor settings

or overspeed the engine.

6) Do not strain the machine too much and do not

use a small machine for heavy-duty works. If you

use the right machine, you will reduce the risk of

hazards and improve the quality of your work.

7) Check that when the machine is running idle,

there is no movement of the cutting device and, af-

ter pressing the throttle trigger, the engine quickly

returns to minimum speed.

8) Ensure that the blade does not come into violent

contact with foreign bodies and beware of the pos-

sibility of material being thrown up by the bla des.

9) Always keep the machine connected to the web-

bing when working.

10) Stop the engine:

– whenever you leave the machine unattended.

– before refuelling.

– during movements between work areas.

11) Stop the engine and disconnect the spark

plug cable:

– before cleaning, checking or working on the ma-

chine;

– after striking a foreign object. Inspect the ma-

chine for any damage and make repairs before

restarting it again;

– if the machine starts to vibrate abnormally: nd

the cause of the vibration immediately and have

it inspected at a Specialised Centre.

– when the machine is not in use.

D) MAINTENANCE AND STORAGE

1) Keep all nuts, bolts and screws tight to be sure

the equipment is in safe working condition. Rou ti ne

maintenance is essential for safety and for

maintaining a high performance level.

2) Do not store the machine with fuel in the tank in

an area where the fuel vapours could reach an o pen

ame, a spark or a strong heat source.

3) Allow the engine to cool before storing in any

SAFETY REQUIREMENTS

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina TB 250 JD in the language / languages: All languages as an attachment in your email.

The manual is 1,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina TB 250 JD Manual

Product: