Manual Alpina SH 2500 (page 20 of 25) (All languages)

731996

Zoom out

Zoom in

1/25

OPERATING INSTRUCTIONS

NOTE - The number which precedes each paragraph

links the references in the text to the respective illustra-

tions (listed on page 2 and following pages).

1. COMPLETING ASSEMBLY

NOTE - The machine can be supplied with some

pre-assembled parts.

WARNING - Unpacking and completing the assem-

bly should be done on a at and stable surface,

with enough space for handling the machine and its

packaging, always using suitable equipment.

Disposal of the packaging should be done in accor-

dance with the local regulations in force.

1.1

Machine assembly

Grasp the working head (1) as indicated and position it

over the frame (2), taking care to insert the protruding part

(3) in its slot (4). Fully tighten the four knobs (5).

Assemble the wheels (6), using the pins (7), washers (8)

and split pins (9) in the indicated sequence.

Apply the wheel covers (10) inserting the tabs (11) in

their slots (12).

IMPORTANT - When assembly is completed, the di-

stance between the pressure plate and the shredding

roller must be adjusted as indicated at point 4.1.

2. CONTROL DESCRIPTION

2.1

Motor control

The motor is controlled by two buttons:

– Green button (1-I ) = Run

– Red button (2-O) = Stop

The tool will switch o in the event of a power shortage.

Press the green button (1) again to restart the motor.

2.2

Rotation direction switch

The motor rotation direction is controlled by two buttons:

– Black button (3-▼) = Operating rotation direction, fa-

vour ing material feeding.

– Black button (4-▲) = Rotation in opposite direction to

free jammed material; a led (5) li-

ghts up to indicate that rotation is

in the opposite direction.

When the motor is started, the operating rotation direction

is automatically set which favours material feeding.

3. USING THE MACHINE

IMPORTANT:

• Use the machine on rm level ground, keeping feet

at the same level as the wheels.

• When starting the machine there can be momentary

drops in voltage. Make sure that its impedance is lower

than 0.42 ohm to prevent disturbances to other equip-

ment connected to the mains supply.

• If the motor stops because it is overheated while wor-

king, you must wait about 5 minutes before restarting it.

3.1

Machine set-up

Fit the collection box (1) in the space beneath the machine

and pull the safety handle (2) up to lock it and enable the

motor to be started.

If the handle is not positioned properly, the motor will not

start.

3.2

Machine connections

Properly insert the extension lead socket (11) to the ma-

chine plug (12) as indicated, then insert the extension

lead plug in the mains socket (13).

3.3

Motor start-up and operating modes

Press the green button (1-I ) to start the motor. Always

feed the material to be shredded from the right side

through the hopper’s feed opening (2). If necessary, use

the provided plunger (3) to help push material through.

Advice for shredding

• Avoid shredding wet material.

• Strip branches with too many ramications and remove

the side shoots.

• Do not shred branches with a diameter exceeding 4 cm;

it may be necessary to reduce the maximum diameter

of branches to be shredded according to wood type

and freshness.

• Always feed small quantities of material in order to not

clog the feeding hopper.

• Avoid blocking the discharge chute to prevent shredded

material from backing up through the feeding hopper.

• Shred garden waste only in small quantities, particularly

when humid or wet; alternate it with branches to prevent

clogging.

• Do not shred kitchen waste or other material with a

non-solid consistency.

Important recommendations

• Do not shred excessively long branches to prevent inju-

ries from branches that may lash out uncontrollably.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina SH 2500 in the language / languages: All languages as an attachment in your email.

The manual is 1,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina SH 2500 Manual

Product: