Manual Alpina ATR 600 E (page 15 of 21) (All languages)

731974

Zoom out

Zoom in

1/21

USING THE MACHINE 9

• Aligning the power unit

– Press the pedal (4) and align the power unit (5)

with one of the three allowed positions.

– Make sure the power unit is rmly assembled

before switching the motor on.

– Rotate the cutting limit indictor (6) towards the

front when working near trees, curbs or fences

to prevent them coming into contact with the

cutting device.

3. WORKING TECHNIQUES

WARNING! Use ONLY nylon lines. The

use of metal lines, plasticised metal lines and/

or lines not suitable for the head can cause

serious injuries and wounds.

During use it is advisable to stop the motor peri-

odically and remove the weeds wound round the

machine, so as to prevent overheating due to the

grass caught under the guard.

Remove the caught-up grass with a screwdriver.

WARNING! Do not use the machine

for sweeping, tilting the cutting line head. The

power of the motor could throw objects and

small stones 15 metres or more, causing dam-

age and injuries to people.

• Cutting in motion (Scything) (Fig. 6)

Proceed at a regular pace, with a circular motion

similar to a traditional scythe, keeping the cutting

device parallel to the ground.

First try cutting at the right height in a small area,

so as to then achieve a uniform cutting height

keeping the cutting line head at a constant dis-

tance from the ground. For heavier cutting it can

be useful to tilt the cutting line head by about 30°.

WARNING! Do not work in this way if

there is the possibility of causing objects to

be thrown, which could harm people and ani-

mals and cause damage.

• Cutting near fences/foundations

Slowly approach the cutting line head to fences,

posts, rocks, walls, etc. without hitting them hard.

If the line strikes a solid object it could break or

become worn; if it gets tangled in a fence it could

break abruptly. In any case, cutting around pave-

ments, foundations, walls, etc. can cause greater

wear than normal to the line.

• Cutting round trees

Walk round the tree from left to right, approaching

the trunks slowly so as not to strike the tree with

the line and keeping the cutting line head tilted

forward slightly.

Remember that the nylon line could lop or damage

small shrubs and that the impact of the nylon line

against the trunk of bushes or trees with soft bark

could seriously damage the plant.

• Adjusting line length when working (Fig. 7)

This machine is tted with a “Tap & Go” head.

To release more line, tap the cutting line head

against the ground with the motor running; the line

will be released automatically and the knife cuts o

the excess length.

If the line is not long enough:

– stop the motor and disconnect the extension

lead from the mains:

– press the bottom of the head and tug on the

ends of the line, until it reaches the desired

length.

If the line has run out, the coil must be replaced.

WARNING! After working on the cut-

tingline head, always put the machine in a

working position before starting the motor.

4. END OF OPERATIONS

When you have nished your work:

– Switch o the motor as indicated above (Chap.

6).

WARNING! Allow the motor to cool

before storing in any enclosure.

To reduce re hazards, clean the machine

thoroughly to get rid of any remains of grass,

leaves or excess grease, never leave contain-

ers with the cut debris inside the storage area.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina ATR 600 E in the language / languages: All languages as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina ATR 600 E Manual

Product: