Manual Alpina ATR 26 J (page 20 of 27) (All languages)

731964

Zoom out

Zoom in

1/27

– Carefully open the fuel tank cap to allow the

pressure inside to decrease gradually. Use

a funnel to rell and avoid lling the tank to

the brim.

WARNING! Always close the fuel tank

cap firmly.

WARNING! Immediately clean all traces

of fuel which may have dripped on the ma-

chine or the ground and do not start the en-

gine until the petrol fumes have dissipated.

3. USING THE MACHINE

3.1 STARTING THE MACHINE

WARNING! The machine must be started

in an area at least 3 metres from where you

refilled the fuel tank.

Before starting the engine:

– Place the machine rmly on the ground.

3.1.1 Cold starting

WARNING! A “cold” start of the engine

means starting it after at least 5 minutes from

when it was switched off or after refuelling.

To start the machine (Fig. 5):

1. Set the switch (1) to position «I».

2. Operate the choke, turning the lever (4) to the

«B» position”.

3. Press the primer device button (5) 3 or 4 times

to prime the carburettor.

4 Press the safety lever (3), activate the throttle

trigger (2) and hold it in this position using

the shutter button (7); then release the safety

lever (3).

5. Hold the machine rmly on the ground with

one hand on the power unit, in order not to lose

control of the machine during startup (Fig. 6).

IMPORTANT To prevent distortions, the drive

tube must not be used as a support for the hand

or knee during startup.

6. Pull the starter grip slowly for 10 - 15 cm un-

til you feel some resistance, then tug it a few

times until you hear the engine turn over.

IMPORTANT To avoid breaking the starter ca-

ble, do not pull the whole length of it or let it slide

along the edge of the cable guide hole. Release

the starter grip gradually, to avoid letting it fly back

uncontrollably.

7. Pull the starter grip again until the engine

starts as normal.

WARNING! Starting the engine with the

choke engaged causes the cutting device to

move, only stopping when the choke is dis-

connected.

8. When the engine is started, disconnect the

starter by turning the lever (2) to «ON».

9. Disconnect the shutter (7 - if provided) briey

activating the throttle trigger (2), to take the

engine back to minimum speed.

10. Let the engine run idle for at least 1 minute

before using the machine.

IMPORTANT If the starter grip is pulled repeated-

ly with the choke on, it may flood the engine and

make starting difficult.

If you have ooded the engine, remove the spark

plug and gently pull the starter grip to eliminate

any excess fuel; then dry the spark plug elec-

trodes and replace it on the engine.

3.1.2 Warm starting

When warm starting (immediately after stop-

ping the engine), follow the procedure indicated

above in points 1-5-6-7.

3.2 ADJUSTING THE SPEED

OF THE CUTTING DEVICE (Fig. 5)

Cutting device speed is regulated by the throttle

trigger (2), located on the rear handgrip (6).

The throttle trigger only works if the lockout (3) is

pressed at the same time.

The movement is transmitted from the engine

to the transmission shaft by a centrifugal mass

clutch that prevents the shaft from moving when

the engine is running at minimum speed.

WARNING! The cutting device must not

move when the engine is running idle. If the

cutting device moves when the engine is

running idle, contact your dealer to correctly

regulate the engine.

The correct running speed will be achieved by

pressing the throttle trigger (2) as far as possible.

IMPORTANT Avoid using the engine at full pow-

er for the first 6-8 working hours.

3.3 STOPPING THE MACHINE (Fig. 5)

To stop the machine:

– Release the throttle trigger (2) and allow the

engine to run idle for a few seconds.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina ATR 26 J in the language / languages: All languages as an attachment in your email.

The manual is 1,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina ATR 26 J Manual

Product: