Manual Alpina ATR 26 J (page 19 of 27) (All languages)

731964

Zoom out

Zoom in

1/27

OF THE CUTTING LINE HEAD (Fig. 3)

a) Assembly

– Block rotation of the shaft (1) with a proper

wrench.

– Fit the cutting line head (2) screwing it clock-

wise.

c) Disassembly

– Block rotation of the shaft (1) with a proper

wrench.

– Remove the cutting line head (2) unscrewing it

anticlockwise.

1.4 MOUNTING THE ROD (Fig. 4)

– Pull out the stop pin (1) and push the lower

part of the rod (2) right down until the stop pin

(1) clicks into the hole (3) in the rod. This is

easier to do if you rotate the bottom of the rod

(2) slightly in both directions. The pin (1) is in

place when it is completely lodged in the hole.

– Once inserted, tighten the knob (4) securely.

2. PREPARING TO WORK

2.1 CHECKING THE MACHINE

Before starting work please:

– check that all the screws on the machine and

the cutting device are tightly fastened;

– make sure the cutting device is not damaged;

– make sure the protection devices are well fas-

tened and working eciently;

– check the handgrips are well fastened.

2.2 PREPARING THE FUEL MIXTURE

This machine is tted with a two-stroke engine

which requires a mixture of petrol and lubricat-

ing oil.

IMPORTANT Using petrol alone will damage the

engine and is cause for invalidation of the war-

ranty.

IMPORTANT Use only quality fuels and oils to

maintain high performance and guarantee the du-

ration of the mechanical parts over time.

2.2.1 Petrol characteristics

Only use unleaded petrol with a fuel grade of at

least 90 ON.

IMPORTANT Unleaded petrol tends to create de-

posits in the container if preserved for more than 2

months Always use fresh petrol!

2.2.2 Oil characteristics

Only use top quality synthetic oil specically for

two-stroke engines.

Your Dealer can provide you with oils which have

been specically developed for this type of en-

gine, and which are capable of guaranteeing a

high level of protection.

The use of these oils makes it possible to pre-

pare a 2,5% mixture, consisting in 1 part oil to

40 parts petrol.

2.2.3 Preparation and preservation

of the fuel mixture

DANGER! Petrol and the fuel mixture are

highly inflammable!

– Keep the petrol and fuel mixture in homolo-

gated fuel containers, in a safe place, away

from any flames or heat sources.

– Never leave the containers within the reach

of children.

– Never smoke whilst preparing the mixture

and avoid inhaling the petrol fumes.

To prepare the fuel mixture:

– Place about half the amount of petrol in a ho-

mologated tank.

– Add all the oil, according to the chart.

– Add the rest of the petrol.

– Close the top and shake well.

IMPORTANT The fuel mixture tends to age. Do

not prepare excessive amounts of the fuel mixture

to avoid the formation of deposits.

IMPORTANT Keep the petrol and fuel mixture

containers separate and easily identifiable to

avoid the mistake of using one in place of the

other.

IMPORTANT Periodically clean the petrol and

fuel mixture containers to remove any eventual

deposits.

2.3 REFUELLING

DANGER! Never smoke whilst refuelling

and avoid inhaling the petrol fumes.

WARNING! Carefully open the tank top

as pressure could have formed inside.

Before refuelling:

– Shake the fuel mixture container well.

– Place the machine on a at stable surface,

with the fuel tank cap facing upwards.

– Clean the fuel tank cap and the surrounding

area to avoid any dirt from entering the tank

during relling.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina ATR 26 J in the language / languages: All languages as an attachment in your email.

The manual is 1,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina ATR 26 J Manual

Product: