731527
78
Zoom out
Zoom in
Previous page
1/251
Next page
7
Operation






Oil level check (par. 5.1.1) - - -
Oil change
1
(par. 6.3) - -
Cleaning the silencer
and the engine (par. 7)
- - -
Checking and cleaning
the air lter
2
(par. 8)
- - -
Changing the air lter (par. 8) - - -
Spark plug check (par. 9) - - -
Changing spark
plugs (par. 9)
- - -
Fuel lter check
3
- - -
1
Change the oil every 25 hours if the engine is
operating under heavy load or in hot weather.
2
Clean the air lter more frequently if the
machine is operating in dusty areas.
3
To be carried out by a Specialised Centre.
6.3 OIL CHANGE
For the required type of oil, observe the
indications provided in the technical data table.
Drain the oil out while the engine
is warm, being careful not to touch
the hot engine nor the drained oil.
Unless otherwise stated in this
machine Instruction Manual, to
change the oil it is necessary to:
1. Place the machine on a at surface.
2. Clean around the ller cap and unscrew
the cap with dipstick (g. 6.A).
3. Provide a suitable container for collecting
the oil and unscrew the drain plug (g. 6.G).
4. Ret the drain plug (g. 6.G) and tighten it.
5. Top up with new oil (par. 5.1.1).
6. Check that the oil level has reached the
«MAX» notch on the dipstick (g. 6.B).
7. Close the cap (g. 6.A) again and clean up
any traces of oil that was possibly spilt.
6.4 CLEANING THE SILENCER
AND THE ENGINE
The silencer must be cleaned
when the engine is cold.
Use a jet of compressed air (g. 7.A) to remove
any debris and dirt that could cause a re
from the silencer and its protective cover.
Ensure that the cooling air intakes
are not obstructed (g. 7.A).
Clean the plastic parts with a sponge
(g. 7.B) soaked in water and detergent.
6.5 AIR FILTER MAINTENANCE
1. Clean around the lter cover (g. 8.A).
2. Take the cover o (g. 8.A) by
unscrewing the two knobs.
3. Remove the ltering element (g. 8.B + 8.C).
4. Take the pre-lter (g. 8.C) out
of the cartridge (g. 8.B).
5. Tap the cartridge (g. 8.B) on a solid
surface and blow it from the inside with
compressed air to remove dust and debris.
6. Wash the pre-lter sponge(g. 8.C) with
water and detergent and leave it to air dry.
IMPORTANT Do not use water,
petrol, detergents or any other
products to clean the cartridge.
IMPORTANT The pre-lter sponge
(g. 8.C) must NOT be oiled.
1. Clean out any dust and debris from inside
the lter housing (g. 8.D) being careful to
close the extraction duct with a cloth (g. 8.E)
to stop them from getting into the engine.
2. Remove the cloth (g. 8.E) , place the ltering
element (g. 8.C + 8.B) in its housing and
put the cover back in place (g. 8.A).
6.6 SPARK PLUG CHECKS
AND MAINTENANCE
1. Take the spark plug down (g. 9.A)
using a socket wrench (g. 9.B).
2. Clean the electrodes (g. 9.C) with a metal
brush, removing any carbonaceous build-up.
3. Using a thickness gauge (g. 9.D)
ensure the gap between electrodes is
correct (0.6 - 0.8 mm).
4. Put the spark plug back in (g. 9.A) and
tighten rmly using a socket wrench (g. 9.B).
Replace the spark plug if the electrodes are
burnt or if the porcelain is broken or damaged.
78


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpina AT2 72 HA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpina AT2 72 HA in the language / languages: All languages as an attachment in your email.

The manual is 7,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info