541393

Allied Telesis AT-9724TS Manual

34
Zoom out
Zoom in
Previous page
1/197
Next page
Parameter Description
State Toggle the State <Enabled> field to either enable or disable a given port or group of ports.
Speed/Duplex Toggle the Speed/Duplex field to either select the speed and duplex/half-duplex state of the port.Auto
denotes auto-negotiation between 10 and 100Mbps devices,in full- or half-duplex.The Auto setting allows the
port to automatically determine the fastest settings the device the port is connected to can handle,and then to
use those settings.
The other options are
Auto,10M/Half,10M/Full,100M/Half and 100M/Full,1000M/Full_M and
1000M/Full_S.There is no automatic adjustment of port settings with any option other than Auto.
The Switch allows the user to configure two types of gigabit connections;
1000M/Full_M and 1000M/Full_S.
Gigabit connections are only supported in full duplex connections and take on certain characteristics that are
different from the other choices listed.
The
1000M/Full_M (master) and 1000M/Full_S (slave) parameters refer to connections running a 1000T cable
for connection between the Switch port and other device capable of a gigabit connection.The master setting
(
1000M/Full_M) will allow the port to advertise capabilities related to duplex,speed and physical layer type.The
master setting will also determine the master and slave relationship between the two connected physical layers.
This relationship is necessary for establishing the timing control between the two physical layers.The timing
control is set on a master physical layer by a local source.The slave setting (1000M/Full_S) uses loop timing,
where the timing comes form a data stream received from the master.If one connection is set for
1000M/Full_M,the other side of the connection must be set for 1000M/Full_S.Any other configuration will
r
esult in a link down status for both ports.
Flow Control Displays the flow control scheme used for the various port configurations.Ports configured for full-duplex use
802.3x flow control,half-duplex ports use backpressure flow control,and
Auto ports use an automatic selection
of the two.The default is
Disabled.
Learning Enable or disable MAC address learning for the selected ports.When Enabled,destination and source MAC
addresses are automatically listed in the forwarding table.When learning is
Disabled,MAC addresses must be
manually entered into the forwarding table.This is sometimes done for reasons of security or efficiency.See the
section on
Forwarding/Filteringfor information on entering MAC addresses into the forwarding table.
The default setting is Disabled.
Click
Apply to implement the new settings on the Switch.
6-5 Port Description
The AT-9724TS supports a port description feature where the user may name various ports on the Switch.To assign names to various ports,click the Port
Description
on the Configurationmenu:
Figur
e 6- 6.
Port Description Setting and Port Description Table window
Use the
From and To pull down menu to choose a port or range of ports to describe and Unit to choose the Switch in the switch stack,and then enter a
description of the port(s).
Click
A
pply
to set the descriptions in the P
or
t Descr
iption T
a
b
le
.
33
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allied Telesis AT-9724TS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allied Telesis AT-9724TS in the language / languages: English as an attachment in your email.

The manual is 8,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info