The AT-9724TS has 24 1000T Gigabit ports that may be used in uplinking various network devices to the Switch,including PCs,hubs and other switches to
provide a gigabit Ethernet uplink in full-duplex mode.
In addition,the AT-9724TS is equipped with 4 SFP (Small Form Factor Portable) combo ports,which are to be used with fibre-optical transceiver cabling in order
to uplink various other networking devices for a gigabit link that may span great distances.These 4 SFP ports support full-duplex transmissions,have auto-
negotiation and can be used with AT-MG8LX10 (1000LX),AT-MG8SX (1000SX) and AT-MG8ZX (1000ZX) transceivers.These four ports are referred to as
“combo” ports which means that both the SFP ports and the 1000T ports are numbered the same (21–24) and cannot be used simultaneously.Attempting to use
the ports simultaneously will cause a link down status for the 1000T ports.SFP ports will always have priority over these 1000T ports.
Also included at the rear of the Switch are two 10-gigabit stacking ports used to stack up to twelve switches in a ring topology.The AT-9724TS may be used as
the master unit of a switch stack when utilizing these ports and,in total,may provide a stacking solution of up to 288 gigabit ports.
Note:The four SFP combo ports on the Switch,numbered 21–24 cannot be used simultaneously with the corresponding 1000T ports,numbered
21–24.If both ports are in use at the same time (ex.port 21 of the SFP and port 21 of the 1000T),the SFP ports will take priority over the combo
ports and render the 1000T ports inoperable.
1-3 Features
•IEEE 802.3z compliant
•IEEE 802.3x Flow Control in full-duplex compliant
•IEEE 802.3u compliant
•
IEEE 802.3ab compliant
•
IEEE 802.3ae compliant (for optional XFP module)
•
IEEE 802.1p Priority Queues
•IEEE 802.3ad Link Aggregation Control Protocol support.
•IEEE 802.1x Port-based and MAC-based Access Control
•IEEE 802.1Q VLAN
•IEEE 802.1D Spanning Tree,IEEE 802.1W Rapid Spanning Tree and IEEE 802.1s Multiple Spanning Tree support
•Stacking support in Ring topology
•Access Control List (ACL) support
•IP Multinetting support
•Protocol VLAN support
•
Single IP Management support
•Access Authentication Control utilizing TACACS,XTACACS,TACACS+ and RADIUS protocols
•Dual Image Firmware
•Simple Network Time Protocol support
•
MA
C Notification support
•
System and P
ort Utilization support
•
System Log Support
•
High performance switching engine performs forwarding and filtering at full wire speed up to 128Gbps.
•Full- and half-duplex for all gigabit ports.Full duplex allows the switch port to simultaneously transmit and receive data.It only works with
connections to full-duplex-ca
pable end stations and s
witches.
Connections to a hub m
ust take place at half-duplex.
•
Suppor
t broadcast storm filtering
•
Non-blocking stor
e and f
orward switching scheme capability to support rate adaptation and protocol conversion
•Supports by-port Egress/Ingress rate control
•Efficient self-learning and address recognition mechanism enables forwarding rate at wire speed
•
Support port-based enable and disable
•
Address table:Supports up to 8K MAC addresses per device
•Supports a packet buffer of up to 3 Mbits
•Supports Port-based VLAN Groups
•Port Trunking with flexible load distribution and fail-over function
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Allied Telesis AT-9724TS at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Allied Telesis AT-9724TS in the language / languages: English as an attachment in your email.
The manual is 8,71 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
