541398
107
Zoom out
Zoom in
Previous page
1/134
Next page
Routing 107
Software Release 2.7.1
C613-02021-00 REV F
3. Configure IP.
To enable IP on the router, and assign IP addresses to the interfaces used by
DVMRP for multicast routing, enter the commands:
ENABLE IP
ADD IP INTERFACE=PPP0 IPADDRESS=189.124.7.8
MASK=255.255.0.0
ADD IP INTERFACE=ETH0 IPADDRESS=172.74.1.2
MASK=255.255.255.0
ADD IP INTERFACE=ETH1 IPADDRESS=172.74.2.2
MASK=255.255.255.0
4. Configure IGMP.
To enable IGMP on the router, and on the interfaces that have IP host
connected to them, so that the router can maintain its group membership
data, enter the commands:
ENABLE IP IGMP
ENABLE IP IGMP INTERFACE=PPP0
ENABLE IP IGMP INTERFACE=ETH0
ENABLE IP IGMP INTERFACE=ETH0
5. Configure DVMRP
To enable DVMRP on the router and on each interface over which it is used
for multicast routing, enter the commands:
ENABLE DVMRP
ADD DVMRP INTERFACE=ETH0 METRIC=1
ADD DVMRP INTERFACE=ETH1 METRIC=1
ADD DVMRP INTERFACE=PPP0 METRIC=6
Configure multicast routing using DVMRP on Router C.
1. Set the system name.
To set a unique system name for the router, enter the command:
SET SYS NAME=C-dvmrp
2. Configure Frame Relay.
To configure a Frame Relay interface over a synchronous port to Router D,
and add a data link circuit to the Frame Relay interface, enter the
commands:
CREATE FRAMERELAY=0 OVER=SYN0 LMISCHEME=NONE
ADD FRAMERELAY=0 DLC=20
3. Configure ISDN.
Set up an ISDN call to Router A for DVMRP multicast traffic. This call
must have the same name as the ISDN call from Router A, and the opposite
precedence. Enter the command:
ADD ISDN CALL=DVMRP OUTSUB=LOCAL SEARCHSUB=LOCAL
PRECEDENCE=IN NUM=7654321
107


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allied Telesis AR410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allied Telesis AR410 in the language / languages: English as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info