541347
11
Zoom out
Zoom in
Previous page
1/28
Next page
WZ16:2DX
AND
WZ12:2DX U
SER
G
UIDE
11
NO USER SERVICEABLE PARTS INSIDE.
SUPPLY VOLTAGE RANGE:
100 - 240V
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
47-63Hz ~ 30W MAX
WARNING - THIS APPARATUS MUST BE EARTHED.
REFER TO USER GUIDE BEFORE CONNECTING SUPPLY
TO REDUCE THE RI SK OF FI RE OR ELECTRI C SHOCK
DO NOT EXPOSE THI S APPARATUS TO RAIN OR MOISTURE.
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
REPLACE FUSE WITH SAME TYPE AND RATING
WARNING: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
ATTENTION: REMPLACER LE FUSIBLE AVEC UN DES MEMES CARACTERISTIQUES.
100 - 240V~ T500mA 250V 20mm
CAUTION
FUSE
OF F
AC MAINS IN ~
ON
~
Connecting Mains Power
Refer to the
SAFETY WARNING
on page 5 of this Guide.
Check that the correct mains lead with moulded plug has been
supplied with your console. Read and understand the warnings
and instructions printed on the rear panel and reproduced here.
The power supply accommodates mains voltages within the
range 100-240V without changing any fuses or settings.
It is standard practice to turn connected power amplifiers down
or off before switching the console on or off. Ensure that the
IEC mains plug is pressed fully into the rear panel socket before
switching on.
E
ARTHING
The connection to earth (ground) in an audio system is important for two reasons:
1.
SAFETY
- To protect the operator from high voltage shock associated with the AC mains supply
feeding the system, and
2.
AUDIO PERFORMANCE QUALITY
- To minimise the effect of earth (ground) loops which result
in audible hum and buzz, and to shield the audio signals from interference.
For safety it is important that all equipment earths are connected to mains earth so that exposed
metal parts are prevented from carrying high voltage which can injure or even kill the operator. It is
recommended that the sound engineer check the continuity of the safety earth from all points in the
system including microphone bodies, guitar strings, multicore cases, equipment panels ...
The same earth is also used to shield audio cables from external interference such as the hum
fields associated with power transformers, lighting dimmer buzz, and computer radiation. Problems
arise when the signal sees more than one path to mains earth. An ‘earth loop’ (ground loop)
results causing current to flow between the different earth paths. This condition is usually detected
as a mains frequency audible hum or buzz.
To ensure safe and trouble-free operation please observe the following:
x
Do not remove the earth connection from the console mains plug.
The console chassis is
connected to mains earth through the power cable to ensure your safety. Audio 0V is connected to
the console chassis internally. If problems are encountered with earth loops operate the audio
‘ground lift’ switches on connected equipment accordingly, or disconnect the cable screens at one
end, usually at the destination. It is useful to carry ground lift cable adapters such as short XLR
male to female leads with pin 1 disconnected.
x
Avoid running audio cables next to mains, computer or lighting cables,
or near thyristor
dimmer and power supply units. If unavoidable, cross these at right angles.
x
Use low impedance sources
such as microphones rated at 200 ohms or less to reduce
susceptibility to interference. The console outputs are designed to operate at very low impedance
to minimise interference problems.
x
Use balanced connections where possible
as these provide further immunity by cancelling
out interference that may be picked up on long cable runs. To connect an unbalanced source to a
balanced console input, link the cold input (XLR pin 3 or jack ring) to 0V earth (XLR pin 1 or jack
sleeve) at the console. To connect a balanced console output to an unbalanced destination, link
the cold output to 0V earth at the console.
x
Use professional quality cables and connectors
and check for correct wiring and reliable
solder joints.
x
If you are not sure ...
Have your system checked by a competent engineer, or contact your
local Allen & Heath agent for advice.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath WZ12 mixwizard at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath WZ12 mixwizard in the language / languages: English as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Allen-Heath WZ12 mixwizard

Allen-Heath WZ12 mixwizard User Manual - German - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info