541360

Allen-Heath ML-5000 Manual

38
Zoom out
Zoom in
Previous page
1/60
Next page
38 ML5000 User Guide
K VCA GROUPS
VCA Groups Explained
VCA groups provide an important alternative to
audio subgroups for simultaneously controlling the
level of more than one channel using a single fader.
Unlike an audio subgroup the signal is not routed
through the group fader itself. Instead, you route
the signal directly to the main output. The VCA
group fader sends a DC voltage to remotely control
the assigned channel levels, so providing the group
control. This is possible because each channel has
a pre-pan VCA (voltage controlled amplifier) which
can be controlled by both the channel fader and
group faders. This means that all post-fade outputs
from assigned channels will be affected by the VCA
master faders. Note that the channel pre-fade
(monitor) sends are not affected by VCA groups.
Note that the channel fader always controls the
signal level. If the channel is assigned to one or
more VCA groups then both the channel and the
group faders control the level as if they were in
series. Refer to the diagrams over the page.
The ML5000 has 8 VCA groups. Mono and stereo
input channels can be assigned to one or more
groups. The VCA group assignments can be stored
as part of the console snapshot memory system.
This can be disabled if you want the snapshots to
control the mutes only.
The benefits of VCA grouping
Effects balance is maintained. Because the
channel post-fade sends are affected, the reverb
level returned elsewhere in the console also follows
the group fader movements.
Stereo groups on one fader. Because the level is
controlled before the channel pan circuit, a single
VCA group fader is all that is required to control a
stereo or LCR group. This would take 2 or 3 faders
using audio groups if the channel pan image is to
be maintained.
Multiple output control. The relative balance
between all outputs is maintained when moving
VCA group faders.
Multi-level grouping. A channel can be assigned
to more than one VCA group. This lets you assign
multi-level groups, or even a ‘grand master’,
impossible with audio groups.
Conventional audio groups are still useful when you
need to insert a signal processor such as a
compressor to affect a group of signals, or you need
to feed different groups of signals into the matrix.
However, fewer such groups are usually required
on a VCA equipped console. For this reason the
ML5000 provides the mode switching to reconfigure
unused audio groups as full featured aux sends.
OO
40
30
5
0
10
5
10
20
OO
40
30
5
0
10
5
10
20
OO
40
30
5
0
10
5
10
20
OO
40
30
5
0
10
5
10
20
PAFLPAFLPAFLPAFLPAFLPAFLPAFLPAFL
SAFE
M
U
T
E
SAFE SAFE SAFE SAFE SAFE SAFE SAFE
EDIT
GROUP
SELECT GROUP TO EDIT
M
U
T
E
M
U
T
E
M
U
T
E
M
U
T
E
M
U
T
E
M
U
T
E
M
U
T
E
MUTE
NOM
ASSIGN USING CH MUTES
10
20
OO
40
30
5
0
10
5
10
20
OO
40
30
5
0
10
5
10
20
OO
40
30
5
0
10
5
10
20
OO
40
30
5
0
10
5
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath ML-5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath ML-5000 in the language / languages: English as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info