541382
16
Zoom out
Zoom in
Previous page
1/47
Next page
16 IDR-8 User Guide
Starting Offline with iDR System Manager Software
You need to install the iDR System Manager software on your
PC. This requires Windows 95, 98, NT, ME, 2K or XP.
Although the software comes with the resource CD provided
we recommend that you check the Allen & Heath web site for
the latest version. We are continually updating our software to
add new features or make improvements. Download the web
version if it is more recent than the CD.
IMPORTANT: Do not install this software over a
previous version. The setup utility will install the iDR System
Manager into its own directory so that previous versions can be
retained. A previous version can be uninstalled using the
Windows™ Control Panel Add/Remove Programs application.
Run the self-extracting .exe file to install the software. Follow
the on-screen instructions. Make sure you read the Release
Notes before running the program. These may contain
important information about the new software version.
Start the iDR System Manager from the Start / Programs / Allen
& Heath menu. To open a new session click on the blue icon,
press Ctrl+N, or open the N
ew item in the File menu. Select
the Offline button to start an offline session to get familiar with
the program before you connect the iDR-8 unit. Use the H
elp
menu to learn more about how the software works. You can
archive your settings to load into the iDR-8 later.
Turning the iDR-8 On and Off
Make sure you have read the Important Safety
Instructions printed earlier. Also check that your local
mains supply is compatible with that printed on the rear
panel of the iDR-8. Ensure that the correct mains lead with
moulded plug and IEC connector has been supplied.
To avoid any unexpected audible clicks or thumps
always turn connected power amplifiers down or off before
switching the iDR-8 or any other signal equipment on or off.
Turn the unit on by pressing the rear panel power ON/OFF
switch. The LCD display lights up and the message ‘Please
wait…’ is displayed while the processor boots up. This is
followed by a ‘Recall..’ message if a power-up patch is active.
Finally, the normal display is shown.
Note that ‘normal’ display and control settings depend on the
last configuration loaded and whether a power-up patch has
been set.
Boot up time is normally around 10 seconds. However,
this can be up to 35 seconds if the front panel menu *5.1
DHCP Setup has been set to YES and the unit is not connected
to the network.
Parameters restored on power-up The iDR-8
remembers its unit name and address settings on power up.
The clock is always running so the correct time and day is
shown. Configuration related parameters such as channel
names, stereo linking and scheduled events are restored.
Patch related parameters such as levels, EQ and soft control
settings are recalled only if a power-up patch containing them
has been set. If not, then all patch related parameters are reset
according to factory default. Further details are provided in the
section about Patches later in this user guide, and in the iDR
System Manager Help file.
CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE WITH SAME TYPE AND RATING.
ATTENTION: REMPLACER LE FUSIBLE AVEC UN DES MEMES CARACTERISTIQUES.
THIS APPARATUS MUST BE EARTHED.
WARNING
47-63Hz ~ 90W MAX
100 - 240V~
FUSE: T1.6AL
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
Allen & Heath
Wed 13:44:08
Please wait...
IMPORTANT: The iDR does not recall
its last settings on power up. It initialises to
reset state or recalls a ‘power up’ patch if one
has been set. Read here >>>>>>>>>
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath iDR-8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath iDR-8 in the language / languages: English as an attachment in your email.

The manual is 6,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info