794955

Alecto WS5400 Manual

30
Zoom out
Zoom in
Previous page
1/90
Next page
30
POWER UP THE DISPLAY
1. Plug in the power adapter to power up the console.
2. Once the console is power up, all the segments of the LCD will be shown.
3. The console will automatically enter AP mode and sensor synchronization mode automatically.
MANUAL SYNCHRONISATION OF INDOOR AND OUTDOOR UNIT
Press the [ Sensor / Wi-Fi ] key once for the console to enter sensor Synchronization mode (channel number blinking), and
the console will re-register all the sensors that have already been paired to it before.
Whenever you changed the batteries of the wireless sensor, re-synchronization must be done manually.
1. Change all the batteries to new ones in the sensor.
2. Press [ Sensor / Wi-Fi ] key on the console to enter sensor Synchronization mode.
3. Console will re-register the sensor after its batteries are changed (about 1 minute).
REMOVE SENSOR CONNECTION
User may manually delete any sensor from the console.
1. Press the [ CH / SET ] key until the console shows the display of the selected sensor.
2. Press and hold [ REFRESH ] key for 10 seconds, until its readings are reset “ -- , -°C -- % “ is shown.
WIRELESS SENSOR SIGNAL STRENGHT
1. The console display shows the signal strength of the wireless sensor(s), as per table below:
Signal strength of outdoor
7-in-1 sensor
Signal strength of outdoor
7-in-1 sensor
No signal Weak signal Good signal
2. If the signal has discontinued and does not recover within 15 minutes, the signal icon will disappear. The temperature
and humidity will display “Er” for the corresponding channel.
3. If the signal does not recover within 48 hours, the “Er” display will become permanent. You need to replace the batteries
and then press [ Sensor / Wi-Fi] key to pair up the sensor again.
FACTORY HARD RESET
Indoor display unit
To reset the console and start again, press the [ RESET ] key once or remove the backup battery and then unplug the
adapter. To resume factory settings and remove all data, press and hold the [ RESET ] key for 6 seconds.
Outdoor display unit
To reset the outdoor unit, press the [ RESET ] key once or remove the backup battery. To resume factory settings and
remove all data, press and hold the [ RESET ] key for 6 seconds.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alecto WS5400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alecto WS5400 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5.94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info