627484

Alecto WS-4800 Manual

7
Zoom out
Zoom in
Previous page
1/16
Next page
7
3.4 Clock:
Introduction
The WS-4800 is provided with a built-in DCF receiver which receives the DCF time signal from
Frankfurt. This signal ensures that the clock shows the time very accurately, provided a strong enough
signal is being received.
Automatically:
As soon as you insert the batteries into the indoor unit, the clock will start searching for the DCF
radio signal for the time while the antenna symbol is flashing. After several seconds or minutes the
WS-4800 will start showing the correct time. In extreme cases, it can take over a day before the DCF
time is shown.
Manually:
If the clock cannot receive the radio signal or cannot receive it well enough, you can set the clock
manually as follows:
1. press and hold the button for 2 seconds, 12Hr or 24Hr will appear in the display
2. Use / to set the time format, then briefly press the button
3. use / to set the hours and then briefly press the button
4. use / to set the minutes and then briefly press the button
5. use / to set the seconds to 0 (this allows you to have the clock run synchronously with your own
clock) and then briefly press the button
6. use / to set the year and then briefly press the button
7. use / to set the month and then briefly press the button
8. use / to set the date and then briefly press the button
9. use / to set the hour difference compared to the DCF time. E.g. for use in the Benelux select ‘0’
and then briefly press the button.
10. use / to set the language in which the day must be displayed, you may choose from: EN (English),
FR (French), DE (German), ES (Spanish) or IT (Italian), now briefly press the button.
11. use / to determine whether the clock must switch to daylight saving time or standard time
automatically (AUTO) or whether you prefer to do this manually (OFF), now briefly press the button.
The clock is now set manually.
When the DCF receiver is enabled and a strong signal is being received, the receiver will overwrite the
clock display.
Switching the DCF receiver on/off:
You can turn off the DCF receiver as follows, allowing you to have only the time and date shown on the
display according to your programming:
• turn off: press and hold the RCC OFF button at the rear of the indoor unit for 8 seconds until
the antenna symbol disappears.
You can turn the receiver back on as follows:
• turn on: press and hold the RCC ON button at the rear of the indoor unit for 8 seconds until
the antenna symbol starts flashing.
The symbol in the upper middle part of the display shows the status of the DCF clock:
no symbol: the DCF receiver is disabled; the displayed time is provided by the internal clock
of the WS-4800
flashing: the DCF receiver is enabled and is searching for the DCF signal; the displayed
time is provided by the internal clock of the WS-4800
remains lit: the DCF receiver is enabled and is receiving the DCF signal; the displayed time
and date are provided by the DCF atomic clock in Frankfurt
3.5 To reset measurement data:
After the installation is completed, press and hold the HISTORY button for 10 seconds to delete all of
the measurements made up until that moment. This ensures that you won’t see any measurements at a
later time that were caused by movements during the installation.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alecto WS-4800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alecto WS-4800 in the language / languages: English as an attachment in your email.

The manual is 3,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alecto WS-4800

Alecto WS-4800 User Manual - German - 16 pages

Alecto WS-4800 User Manual - Dutch - 16 pages

Alecto WS-4800 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info