Manual Alecto SA-240 (page 14 of 20) (English, German, Dutch, French, Spanish)

707363

Zoom out

Zoom in

1/20

The SA-240 is a smoke detector set for discovery of ﬁre in the ﬁrst stage. If smoke develops, the SA-240 will

give a loud beep of at least 85dB (A). As part of the link function all the smoke alarms within range will sound

the alarm. We advice to test the smoke detectors weekly using the test button on the detectors. Save this

manual in a safe place or inside of the electricity meter cupboard.

RECOMMENDED INSTALLATION LOCATIONS FOR THE SA-240:

Install the ﬁrst smoke detector near the bedroom. Ensure that it is placed so, if it would detect ﬁre, at least one exit

route would still be accessible. We recommend to place one alarm near each potential blockade of your exit route, so

you are alerted before a ﬁre would block off escape.

Use multiple smoke detectors to increase safety and ensure an alert before the escape route is blocked.

Install at least one smoke detector on each ﬂoor of your house.

Install at least one smoke detector in each room where people smoke or where there is equipment that may

potentially cause a ﬁre.

Smoke and heat will ﬁrst move upwards towards the ceiling; after that the smoke and heat will travel horizontally.

Install the detector on the ceiling. Except for rooms smaller than 1m, you should stay at least 50 cm away from the

wall and 61cm from any corner. Smoke and heat do not gather in such corners, preventing the detector from alerting

you on time.

DO NOT INSTALL IN THE FOLLOWING LOCATIONS:

• The kitchen; Steam from cooking might give a false alarm.

• The shower or bathroom; water damp might cause a false alarm and the moist environment might damage the

detector.

• The garage: The car exhaust might cause a false alarm.

• In front of a fan or nearby the exhaust of an air conditioner or heater.

• In a ceiling nook.

• In rooms where the temperature could reach below 0°C or beyond 40°C.

• Do not paint or otherwise cover this smoke detector.

INSTALLATION INFORMATION:

For your own safety; before installation, ensure all mains power has been disconnected. Once the

installation is fully complete, you may reconnect the 230V mains power.

Attach the ceiling plate using the included plugs and screws to the ceiling on a location of choice. Wall mounting

is not recommended for smoke detection. Remove the plastic foil from the backup battery and place it inside the

battery compartment, minding the polarity. Attach the detachable 230V connection cable to the cables leading to the

electricity meter of 230V , you may attach the white link cable to another cable to lead to the lead-cable of any other

SA-240 model to link both models. Do not attach this cable to the earthing cables.

ATTENTION. Do not switch the phase (brown) and 0-(blue) cables. The smoke detector will not function

correctly if you do this.

Now plug the 230V connection cable you installed into the SA-240. The connector only ﬁts at one single angle. Then

place the detector on the ceiling plate and twist it into place. Now reconnect the power to mains. The green LED

should now light constantly. Perform a ﬁrst test by holding the test key for two seconds. Also see the paragraph:

“Testing”.

Do not place here

Place near here

Minimum distance

SA-240-8712412574636-Manual v2.2

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alecto SA-240 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 3,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alecto SA-240 Manual

Product: