Manual Alde Comfort 2928 (page 14 of 32) (English, German, Dutch, French, Swedish, Finnish)

626264

Zoom out

Zoom in

1/32

Starting the LPG boiler2:2

Open the regulator and service tap for the LPG.1.

Turn the thermostat knob to ignition position (see 2.

g 2). The indicator light for the ignition spark starts

ashing.

Press the thermostat knob down as far as it will go. 3.

Hold it down for about 15 seconds after the indica-

tor light has gone out. (The boiler has ignited as

soon as the warning light goes out, but in order

for the ignition safety cut-out to remain open, the

thermostat knob must be held down for the neces-

sary period).

Release the thermostat knob.4.

Turn it to operating position and set the desired 5.

temperature (see chpt 2:4).

If the indicator light starts ashing immediately after 6.

the thermostat knob has been released the boiler

has not ignited. Press the thermostat knob down

again and repeat the starting procedure as above,

but hold it down a little longer.

You can also check through the window in the lower 7.

front plate whether the boiler is lit.

Should the boiler go out, turn the thermostat knob to

stop position (see g 3). Wait 3 minutes and repeat

the starting procedure.

The boiler is equipped with automatic reignition, which

means that if it goes out for some reason, it attempts

to restart for about 20 seconds (until the safety cut-out

has cut the gas supply). Should the gas run out while

the boiler is in operation, the warning light will start

ashing and continue on until the boiler is shut down or

restarted.

Shutting down the LPG boiler2:3

Turn the thermostat knob clockwise to stop position 1.

(see g 3). After about 20 seconds, a click should

be heard from the gas valve, which means that the

safety cut-out has closed.

Stop the circulation pump on the control panel.2.

Close the service tap for the LPG.3.

NB. When the boiler has gone out, it must not be

reignited until 3 minutes have elapsed.

Setting for maximum comfort2:4

For maximum comfort and economy, it is important to

set the right water temperature in the system. At low

outside temperatures, a higher water temperature is

required than at more normal temperatures. The ideal

setting on the thermostat knob is when the circulation

pump runs about 75% of the time.

When heating a very cold boiler, the thermostat knob

should not be set to maximum temperature imediately,

but at an intermediate position for the rst 10 minutes.

The various gures on the thermostat knob represent

the number of degrees of the water temperature in the

boiler as per g 4.

When it is extremely cold, the gas boiler and the

immersion heater can be run at the same time. This

means that maximum power is obtained from the heat-

ing system. When the heating system is used at a high

altitude, the boiling point of the liquid mixture changes.

In this case the system temperature should be lowered

as per g 5.

In order to utilize the principle of water-born heat in the

best possible way, it is important that air can pass free-

ly under beds and behind back cushions. If the vehicle

has a tted carpet, for example, ensure that the carpet

does not cover the intake hole for the convectors. It is

equally important that the cushions and blankets do

not prevent air circulation behind the back cushions.

Setting the room temperature2:5

The temperature required inside the vehicle should

be set on the knob of the room thermostat, which is

graduated between 5 and 30

Circulation pump2:6

In order to make the heated glycol water circulate,

some form of pump is required. In the expansion ves-

sel of the LPG boiler a 12-volt circulation pump is tted

as standard. The boiler can also be equipped with an

immersion heater with a 240-volt circulation pump. The

choice of which pump to use, and whether it is to run

constantly or be interrupted by the room thermostat, is

made on the boiler’s control panel.

Electrical heating2:7

If the immersion heater is tted on the boiler it can

only be used if you have access to 230/240 volts ~.

The power output is 1050 and 2100 watts respectively.

Choice of power is made on the boiler’s control panel.

Inside the immersion heater’s protective cover, there

are two thermostats. One ensures that the immersion

heater maintains an operating temperature of around

C while the other acts as overheating protection,

which cuts the current automatically if the immersion

heater boils for some reason. If the overheating protec-

tion triggers, it can be reset by pressing in the overheat

reset button on the side of the immersion heater (see

g 6A).

Make sure that textiles and other inammable material

cannot come into contact with the immersion heater.

NB. All electrical work on the immersion heater

must be performed by an authorized person.

EXTERNAL START 3.

(applies only if the immersion heater is tted).

Do you want the vehicle to be heated when you arrive?

If so, your neighbour or the warden can start the heat-

ing without having to enter the vehicle. However, your

boiler must be tted with an immersion heater and

there must be a battery eliminator (art. no. 2921 520)

connected to the boiler.

How to perform an external start:

Plug the battery eliminator into a 230/240-volt 1.

socket.

Plug the 12-volt contact into the power intake on the 2.

boiler’s control panel (see g 1 J).

Select power and circulation pump on the control 3.

panel.

Switch off the main switch in the vehicle.4.

Disconnect the 230/240-volt cable from the external 5.

power supply.

Where can I get an Alde control house and lid in EUROPE for a 2923/2928? Submitted on 29-8-2021 at 17:16
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alde Comfort 2928 in the language / languages: English, German, Dutch, French, Swedish, Finnish as an attachment in your email.

The manual is 1,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alde Comfort 2928

Alde Comfort 2928 Installation Guide - English, German, Swedish - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alde Comfort 2928 Manual

Product: