601589

Al-ko TCS Duotec 2500 Manual

19
Zoom out
Zoom in
Previous page
1/52
Next page
Assembly
456251_a 19
Open the machine
5 loosen the handscrewn (2a).
6 fold back the feeder tube (2b).
7 Place the lower half on the side ans dispose
of the packaging.
8 Position the washers 8,4 x 24 (DIN 9021) and
legs on the housing and insert screws M8 x
35 (3).
9 Attach the legs using the nuts M8 and was-
hers 8,4 x 16 (DIN 125) supplied. (Assembly
the same on left and right side) (4)
ADVICE
For easier assembly of the wheel axle,
do not fully tighten the nuts simply hold
the legs in position the screws.
Assemble wheel axle and wheels
You will need:
1 axle
2 screws M8 x 40
2 washer 8,4 - DIN 125
2 nuts M8
2 wheels with ball bearings
2 extension screws (= wheel axles)
2 nuts M10
2 adjusting washer 15 x 21 x 0,5
2 retainig washer 10,5
1 Using the 2 screws, 2 washers 8,4 and nuts,
screw the axle onto the legs. (5)
2 Ten tighteen the 6 nuts on the legs.
3 Position the lower part of the shredder on the
legs.
4 Place the upper part of the shredder on the
top of the lower part. (6)
5 Allow the upper part to engage int the central
retainer.
6 Push the rod through the holes in the upper
and lower parts of the shredder.
7 Screw the nut back onto the rod. (7)
8 Tighten the handscrew. (2a)
9 The wheels (with ball bearings fitted) are se-
cured to the axle using the extention screw,
adjusting washer 15 x 21 x 0,5, retainig was-
her 10,5 and nut. (8)
10 Fit the wheel covers onto the wheels.
Assembly tools
Included with the shredder is the following:
1 box spanner SW 10
1 open-endde spanner SW 10/8
1 Torx-bitT30
Assembly of feeder funnel
Tools:
1 Screwdriver
4 Bolts M6 x 25
4 Washer A6,4 DIN 9021
1 Fit the projective rubber guard on top of the
tube. (9b)
2 Position the funnel on top of the tube. (9c)
3 Secure the funnel to the tube using the 4
screws and washers. (9d)
Assembly tube
Montage Fülltrichter
Assembly tools:
4 washer 6,4 - DIN 125
4 retaining washer 6,4
1 screw M6 x 25
3 screw M6 x 16
1 Position the tube on top of the shredder. (9a)
2 Secure the tube on top of the shredder.
CLEANING AND MAINTENANCE
CAUTION!
Do not spray with water
Removing feeder funnel
1 Switch off shredder
2 Wait until cutter has com to a complete stop.
3 Disconnect mains plug.
4 Loosen screw and pull out (2a)
CAUTION!
For replacement of this screw only origi-
nal part!
Safety disconnection switch
The safety disconnection switch i acted by pulling
the screw out.
The motor can not be started with the normal ro-
cker switch.
Aftre replacing the feeder funnel with the original
screw, the motor can be re-started with the rocker
switch.
ADVICE
Very important for your own safety!
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko TCS Duotec 2500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko TCS Duotec 2500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info