Manual Al-ko Robolinho 4000 (page 28 of 84) (English, German, Dutch, French)

582879

Zoom out

Zoom in

1/84

Assembly

28 Robolinho

4000

Base station

The base station is connected to the electri-

cal power supply (transformer) using the low-

voltage cable (6).

The base station generates a control signal

and sends this in the boundary cable.

There are two charging contacts on the base

station which contact the charging contacts

(10-1) on the Robolinho (10-2) as soon as it

moves into the base station.

The [HOME key] (1-9) is located on the base

station. Pressing this key causes the Ro-

bolinho

4000 to terminate its current activity

for the day, and it returns automatically to the

base station.

Setting up the base station

1 Place the base station (4-2) in a shady lo-

cation in the garden on smooth level ground

where it will be protected against the rain (5).

Then use lawn pegs (4-1) to secure it in place.

Comply with the specified dimensions when

doing this (12-3).

Boundary cable

The boundary cable is secured with lawn pegs. If

the supplied boundary cable is not large enough

for your lawn, you can obtain an extension ca-

ble from your AL-KO dealer, technician or service

partner.

Remove the 10 mm of insulation from the

boundary cable (6-2) and connect it to one

side (6-1) of the base station. Then continue

to lay the cable as shown (12), complying with

the specified distances.

To avoid damage when mowing, make sure

that the boundary cable is in direct contact

with the ground at all points when you are lay-

ing it.

If there are places where the boundary cable

is not in direct contact with the ground, secure

these with an additional lawn peg

WARNING!

Damage to the boundary cable!

Do not scarify the lawn in the area on eit-

her side of where the boundary cable is

laid.

Spare loops of cable

You should incorporate spare loops of cable

(12-1) at regular intervals in order to allow the

base station to be repositioned or the mowing

area to be extended even after the mowing area

has been laid out. To do this, guide the boundary

cable around a lawn peg, return to the previous

lawn peg, then continue as shown, securing with

another lawn peg.

➯

Select the number of spare cable loops ac-

cording to your own judgement.

Laying options

The boundary cable can be laid on the lawn (8-1)

and as much as 10 cm under the turf (8-2). Have

your dealer carry out the laying under the turf on

your behalf.

➯

If necessary, you can also combine both me-

thods.

Laying the cable around obstacles

When laying the cable around obstacles, maintain

the distances shown in the illustration (12).

If there is a distance of 0 cm between the cables, it

is possible for the cable to be driven over. In most

cases, the best solution.

When the distance is at least 30 cm, the

Robolinho interprets the distance as a path and

moves around the obstacle.

When laying the boundary cable in walkways

(12-4), it is necessary to maintain the minimum

distances from obstacles and the minimum pas-

sage width specified in the illustration (12), other-

wise the Robolinho will not be able to operate cor-

rectly.

ADVICE

Crossovers in the boundary cable lead

to malfunctions because the inside and

outside parts are swapped over.

Connecting the boundary cable to the base

station

1 Remove the insulation from the boundary ca-

ble (6-2) after laying the cable and connect to

the spring terminals.

Connecting the low-voltage cables to the

transformer

1 Unscrew the screws with a screwdriver (6-3)

and connect the low-voltage cables to the

transformer (6-5).

➯

The cables can be connected are requi-

red, there is no need to observe a parti-

cular polarity.

2 Insert the mains plug of the transformer into

the mains socket (6-4).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko Robolinho 4000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 9,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Al-ko Robolinho 4000 Manual

Product: