601550

Al-ko MH 5065 R Manual

14
Zoom out
Zoom in
Previous page
1/60
Next page
en
Startup
14 MH 5065 R
Putting of Weeder Share into Operation
Pull up clutch lever entirely and hold it.
Weeder share will begin to rotate only at the
second half of lever motion.
Breaking of Weeder Share
Loose clutch lever.
Starting reverse drive
Pull up lever for reverse drive as far as it will
go.
Disconnection of reverse drive
Release lever for reverse drive.
Switching off the motor
Set-up saturator lever into position "STOP".
MAINTENANCE AND CARE
CAUTION!
Risk of injury!
Before all maintenance and care, al-
ways switch off the motor and dis-
connect the spark plug connector!
The motor may coast down. After
deactivation, make sure that the mo-
tor is at a standstill!
Always wear work gloves when car-
rying out maintenance on the cutter
blade!
Clean the appliance after every use
Do not spray the machine with water! Pene-
trating water (ignition system, carburettor...)
can lead to malfunctions.
ADVICE
If the machine is inclined to its side, the
carburetor must be pointed upwards.
Professional inspection is always necessary:
After running onto an obstacle
At immediate standstill of the motor
For transmission damage
For defective V-belt
When the cutting blade is bent
When the motor shaft is bent
Refilling of Gear Oil
As a matter of principle, the gear oil should be
changed after 100 operating hours. (oil viscosity
SAE 80).
Oil change
1. Remove brake toe.
2. Remove screwed drain plug.
3. Tilt machine back and suck the oil off by a
pump.
4. Fill in fresh oil. Required oil quantity approx.
0,5 l.
ADVICE
In order to be able to measure the oil le-
vel, the machine has to be tilt back. The
oil has to run out of the feed opening,
shortly before the machine touches the
ground at point A .
5. Close feed opening by screwed drain plug.
Engine
Oil Refilling / Air Filter / Spark Plug
See – Operating instructions delivered by engine
producer.
Setting-up of Bowden cables
Fine setting-up is being made by means of an ad-
justing screw on upper handle and on engine sup-
port (on ends of Bowden cables) .
1. Loose the safety nut.
2. Set up by means of adjusting screw.
ADVICE
Correct Setting-up:Weeder shares can
begin to rotate only in the second half of
lever motion.
3. Tighten the safety nut.
Gas Uptake:
See – Operating instructions delivered by engine
producer.
STORAGE
CAUTION!
Fire hazard!
Do not store fuelled machine in buildings
where the petrol fumes might come into
contact with naked flames or sparks!
ADVICE
Only authorized specialized workshops
or our customer service are allowed to
repair the unit.
Switch the engine off, wait until the weed-
ing shares Stop; unplug the connector of the
sparking plug.
Wear protective gloves when manipulating
the weeding shares.
… 14 …


Need help? Post your question in this forum.

Forumrules
1

Forum

al-ko-mh-5065-r

Reset search

  • Does the alco mh5065r have a separate oil tank from the engine . Submitted on 15-3-2022 at 16:09

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko MH 5065 R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko MH 5065 R in the language / languages: English, German, Dutch, French, Italian, Swedish, Norwegian as an attachment in your email.

The manual is 5,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info