601616

Al-ko lhs 7000 Manual

15
Zoom out
Zoom in
Previous page
1/130
Next page
Log splitter
GB 4
4. Set the splitting table at the level of the
timber to be split (see Illus. 7). The splitting
table should engage securely and be hori-
zontal.
5. In the case of the LHS 6000, LHS 7000
model, the swivel table can be swivelled in-
wards or outwards. The table has to be se-
cured with the engaging lever when swiv-
elled inwards (see Illus. 8).
Warning!
The splitting column moves automati-
cally to the upper end position when the
motor is switched on if the column is in
the lowermost end position.
6. Unscrew the oil inspection rod by 2 turns.
7. Switch on the motor by pressing the green
activation button.
8. Adjust the splitting column stroke if neces-
sary (see Stroke limitation).
9. Position the piece of timber on the splitting
table and secure with the retaining claws.
10. Press both control levers downwards. The
splitting process commences.
11. Raise both control levers when the splitting
process is completed to allow the splitting
column to move upwards.
Caution!
The split timber should only be removed
from the splitting table when the splitting
column is in the upper end position.
Note:
Grease the splitting blade lightly when
splitting extremely tough timber.
Stroke limitation
1. Position a piece of timber on the splitting
table.
2. Press both control levers and move the
splitting blade until it approaches to within 2
cm.
3. Release one control lever and switch off the
motor. The splitting blade remains stationary
in this position.
4. Release the fixing screw (Illus. 9-2), draw the
stroke rod (Illus. 9-1) completely upwards
and tighten the fixing screw firmly.
Transportation
1. Move the splitting blade completely down-
wards and switch off the motor.
Caution!
Pull out the unit plug prior to every
change of location.
Warning!
The oil inspection rod must be screwed
firmly if the log splitter is to be trans-
ported, as hydraulic oil will otherwise
leak out.
2. Loosen the star grip on stand feet then fold
the feet inwards and secure with a star grip.
3. Secure both the control levers at the front
with a rubber band (see Illus. 10).
4. Tilt the splitter slightly to the rear with the
hoop on the splitting column until the wheels
are resting on the ground. The log splitter
can be easily transported in this position.
Maintenance and care
Caution!
Switch off the log splitter and disconnect
from the mains power supply prior to
each working operation with the log
splitter. Repairs to the log splitter should
only be realised by a specialist firm or
workshop.
Caring for the log splitter
Lubricating the splitting column
1. The splitting column should be lubricated
with grease free of resin or acid before every
use. This increases the service life of the
sliding jaws.
Maintenance work
Sharpening the splitting wedge
1. The splitting wedge should be sharpened
with a suitable file if necessary.
Checking the hydraulic oil filling level
Note:
Always check the hydraulic oil when the
splitting column is moved inwards. The
log splitter should be in a horizontal
position.
1. Unscrew the oil inspection rod and wipe with
a clean, lint-free cloth.
2. Insert the oil inspection rod (do not screw it
in) and pull out again. The oil level should be
between the markings "min" and "max" (see
Illus. 11). Top up the hydraulic oil if neces-
sary.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko lhs 7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko lhs 7000 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info