601616

Al-ko lhs 7000 Manual

14
Zoom out
Zoom in
Previous page
1/130
Next page
Log splitter
GB 3
Unpacking/Assembly
Caution!
The log splitter should only be used
when all its component parts have been
completely assembled.
1. Check the package contents (Illus. A). Inform
the dealer if deficiencies are detected.
Note:
Tools required for assembly are depicted
in Illus. C. These are not included in the
scope of delivery.
Mounting the control arms
1. Grease the control arm bearing position top
and bottom (Illus. 2).
2. Insert the control arm and tube in the trans-
verse connection recess (Illus. 2).
3. Insert the retaining pin from above past the
tube to the left and secure below with the
washer and split pin (Illus. 3).
Adjusting the retaining claws
The retaining claws can be adjusted to suit the
diameter of the timber. They should be set to the
same dimension on both sides.
1. Loosen the star grip on the retaining claw
and adjust longitudinally to suit the timber di-
ameter (Illus. 4).
2. Tighten the star grip firmly again.
Mounting the splitting cross
1. Screw the fixing screw (Illus. 5-1) somewhat
into the splitting cross.
2. Mount the splitting cross and screw the fixing
screw into the recess in the splitting blade to
draw the splitting cross upwards completely.
3. Secure in the end position with the locking
nut (Illus. 5-2).
Mains connection
The power supply is established via a
switch/plug socket combination (Illus. A-8).
The switch is fitted with an integrated undervolt-
age release. This prevents the motor from start-
ing again spontaneously in the event of a power
cut. The motor can only be restarted by pressing
the green activation button.
1. Plug the connection cable into the unit.
2. Connect the cable to the mains supply.
Note:
Check the direction of rotation of the
motor in the case of a log splitter with a
three-phase current motor (LHS
7000).
The direction of rotation should corre-
spond to the arrow on the fan cover. A
polarity reversal should be realised in
the plug with the phase inverter if this is
not the case.
Warning!
An incorrect direction of rotation will
damage the hydraulic pump.
Plug polarity reversal
1. Press in the phase inverter in the plug with a
straight screwdriver and turn through 90°
(see Illus. 6).
2. Establish the power supply and check the
direction of rotation of the motor again.
Operation
Caution!
The log splitter should not be operated if
components (e.g. the protective hoops)
are missing or defective or the connec-
tion cable is damaged.
Prior to every use
1. Conduct a visual inspection of the log split-
ter.
2. The log splitter should not be operated if
components are missing, defective or loose.
3. Visually inspect the connection cable. A
defective connection cable (e.g. with cracks,
cuts, crushing damage or bends in the insu-
lation) should not be used.
4. Visually inspect the hydraulic components for
leaks.
Log splitter start-up
Caution!
The log splitter should only be used by
one person.
1. Position the log splitter horizontally on a
level, firm surface.
Do not deposit the log splitter on the connec-
tion cable!
2. Lay the connection cable so that it cannot be
damaged by bending, crushing or otherwise.
3. Loosen the star grips from the housing,
unfold the feet outwards, securing them with
the star grips.
Translation of original user instructions
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko lhs 7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko lhs 7000 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info