Manual Al-ko DRAIN 6004 (page 9 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish, Norwegian, Finnish)

601632

Zoom out

Zoom in

1/100

− rain water,

− chlorine water (pool water),

− water for domestic use,

GB 2 Translation of original user instructions

− waste water with no more than 5% sus-

pended matter and a grain size of max. 30

mm diameter (submersible pumps, types

Drain only)

Prohibited use

Your submersible pump is not intended for per-

manent operation. The pump may not be used to

pump the following liquids:

− drinking water,

− salt water,

− beverages or liquid foods,

− corrosives or chemicals

− acids or combustible, explosive or gas-

forming liquids,

− liquids with a temperature above 35 °C

− sandy water or water containing abrasives,

− waste water containing textile or paper parti-

cles (applicable for submersible pumps,

types Sub only).

Description of the Pump

Submersible pump (Fig. A)

1 Cable terminal

2 Handle

3 Pump housing

4 Multi-size nipple

5 Elbow connector

6 Suction slots

7 Float switch

8 Electric cable

Function of the pump

The submersible pump sucks the liquid to be

pump-ed into the pump through the suction slots

(6) and pumps it out at the outlet.

Thermal protection

Your submersible pump is equipped with a ther-

mal protection switch which automatically swit-

ches off the pump in case of overheating. The

pump will remain off until it has cooled down.

After about 15 - 20 minutes, the pump will auto-

matically switch on.

Setting up and Operating the

Pump

1. Screw the elbow connector (5) into the pump

outlet.

2. Screw the multi-size nipple (4) into the elbow

connector (5).

3. Attach a hose to the multi-size nipple.

You can cut off the tip of the multi-size

nipple to fit the diameter of the hose you

are using. Using a hose with the largest

possible diameter will greatly improve the

performance of the pump.

4. Uncoil the electric cable completely.

Make sure that any electrical connections

are not exposed to water and do not lie

within the outflow of the pump.

When placing the pump in the liquid,

make sure to let it down slowly. You may

need to tilt the pump slightly so that air

trapped in the body is released. Set the

pump on the bottom so that it cannot fall

over. If the bottom should be sandy or

muddy or rocky and uneven, place the

pump on a suitable hard, flat surface or

suspend it from a rope attached to a

secure object. Make sure to leave ade-

quate room between the pump and the

bottom so that it cannot suck up solid

matter.

Make sure that the pump does not suck in

solid matter. Sand or other abrasive

particles suspended in the liquid will lead

to increased wear and tear and may

impact the performance of your pump.

Before lowering the pump into a well or a

cistern, attach a rope to the handle. When

placing the pump inside a cistern, make

sure that the shaft is large enough for the

pump to fit. For min. shaft dimensions,

see Figure B.

Place a cover over the cistern so that no

one will fall in.

5. Plug the pump into the socket. As soon as

the pump has reached the cut-in (= START)

level, the float switch will automatically

switch the pump on. When the liquid has

fallen below the cut-off (=STOP) level, the

pump will automatically switch off, see tech-

nical data.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko DRAIN 6004 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Al-ko DRAIN 6004 Manual

Product: