594634
16
Zoom out
Zoom in
Previous page
1/96
Next page
en
Startup
16 BM 660-870/875/5001R
Travel transmission
The gear oil is a factory fill.
Always observe the operating instructions
supplied by the engine manufacturer.
Höhe des Führungsholm einstellen
Setting the handlebar height
Setting the handlebar height
The height is usually adjusted to hip level.
1. Loosen the screws on the housing console.
2. Set the height of the handlebars using the lon-
gitudinal holes.
3. Retighten the screws.
Depending on the model, the handlebar can ad-
ditionally be adjusted using the upper or lower
height settings on the housing console.
Einstellen der Schnitthöhe
Setting the cutting height
The cutting height is adjusted using the skids.
Standard cutter bar
steplessly adjustable cutting height up to approx.
6 cm
Loosen nuts.
Move the skids to the required height.
Retighten the nuts.
CAUTION!
Both skids must be set to the same
height!
ESM cutter bar
Mounting the skid holders as skids
The cutter bar cuts close to the ground.
The cutter bar cuts close to the ground, the curved
side points downwards.
Mounting adjustable skids
steplessly adjustable cutting height up to approx.
6 cm.
Mount the adjustable skid holders as shown
in the illustration, the curved side points up-
wards.
Mount the skids as shown in the illustration.
Setting the cutting height
Loosen the nuts (2 nuts per skid).
Move the skids to the required height.
Retighten the nuts.
CAUTION!
Both skids must be set to the same
height!
Starting the engine
CAUTION!
The clutch levers for the wheel and cutter
drives must not be engaged when star-
ting the engine!
Set the throttle lever to the << START>> position.
Press the primer button 3x with intervals of ap-
prox. 2 seconds.
If the temperature is below 10° C, press the primer
button 5x.
ADVICE
Do not press primer buttons when en-
gine is warm.
Quickly pull out the starter cable and then allow it
to slowly rewind.
Falls der Motor nach 3 Zugversuchen nicht an-
springt Punkt 10. und 11. wiederholen.
As soon as the engine is running, set the throttle
lever between the "start" and "stop" positions ac-
cording to the desired engine speed.
To start mowing, move the lever to the <START>
position - (full throttle).
ADVICE
Wenn der Motor aus Kraftstoffmangel
ausgegangen ist, Kraftstoff nachfüllen
und den Motor nach Punkt 10. und 11.
wieder starten.
Switching on scythe attachment (11)
Swivel operator presence control (11-1) away.
Push clutch lever (11-2) fully down and hold it
there.
DANGER!
The mowing mechanism is not allowed
to start moving until the lever has moved
through half of its travel, adjust the Bow-
den cable if necessary – (see: Adjusting
Bowden cables).
Switching on travel drive (11)
Pull clutch lever (11-3) against the handlebar and
hold it there.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko BM 875 III at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko BM 875 III in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info