496641

Akai professional MAX49 Manual

5
Zoom out
Zoom in
Previous page
1/88
Next page
5
13. [LATCH] – This button works in conjunction with the internal Arpeggiator or the Sequencer, depending
on which is currently selected (indicated by its LED button).
Arpeggiator: When the Arpeggiator is on and [LATCH] has been enabled, you can hold down a
combination of keys, and the Arpeggiator will memorize and continue to arpeggiate these notes, even
after you lift your fingers. There are a couple of ways to use the [LATCH] function:
a. While holding down the keys, you can add more notes to the arpeggiated chord by pressing down
additional keys.
b. If you press the keys, release them, and then press down a new combination of notes, the
Arpeggiator will memorize and arpeggiate the new notes.
Sequencer: When the Sequencer is on and [LATCH] has been enabled, you can press a key on the
keyboard to trigger the Sequencer, which will keep playing once you release that key. (The Sequencer
can only be latched in this way when its Start/Stop setting is set to Note On/Note Off. See the
SEQUENCER part of the EDIT MODE section for more information.)
14. TOUCH FADERS – Each fader can be used to send continuous control data to a desktop audio
workstation or external MIDI device. These faders also can also set the MIDI note or velocity of each
step in a Sequence. An LED on the edge of each fader represents its current value/setting (the exact
numerical value will also be displayed in the LCD).
15. S-SWITCHES – These LED buttons serve three functions:
a. Pressing one of these buttons after pressing [TIME DIV] will select the Time Division (the
available values are printed under each button).
b. These LEDs will also light up to indicate which TOUCH FADERS are being used in the current
Sequence.
c. When playing a Sequence, these buttons will illuminate to indicate the steps.
16. FADER/SWITCH BANK BUTTONS – These four buttons switch the TOUCH FADERS and S-
SWITCHES between 4 available banks, with each bank representing 8 steps of a possible 32-step
sequence.
17. [TIME DIV] – Press this button to change the Time Division of the Arpeggiator or Sequencer, then
press an S-SWITCH (on the right) to select the desired Time Division.
18. [SEQ NOTE] – Press this button to put the TOUCH FADERS in Sequence Note Mode. In this mode,
the faders' positions determine the pitch of the notes of each step of a Sequence.
19. [SEQ CC] – Press this button to put the TOUCH FADERS in Sequence CC Mode. In this mode, the
faders' positions determine the MIDI CC of each step of a Sequence.
20. [MIDI] – Press this button to put the TOUCH FADERS in MIDI Mode. In this mode, you can use the
faders to send MIDI CC messages.
21. [VALUE] (Push to Enter) – This dial is used to increment and decrement Presets, parameter values
and settings. This dial also functions as an [ENTER] button when it is pressed down.
22. CURSOR BUTTONS – These buttons are used to navigate through the fields of menus and options.
23. [SHIFT] – Hold this button down to access the secondary functions of the four mode buttons to its right.
24. [EDIT] / [STORE] – This button calls up Edit Mode, which allows you to edit the behavior of the
keyboard, pads, buttons, faders and default settings for each Program. Hold [SHIFT] and press this
button to store the current Program.
25. [PROGRAM] / [STANDARD] – This button calls up Program Mode. You can select and recall different
Programs in this mode. Hold [SHIFT] and press this button to automatically select the last used
Program.
26. [GLOBAL] / [HUI] – This button calls up Global Mode, where MIDI reset commands and global system
preferences are set. Hold [SHIFT] and press this button to automatically select the HUI Program.
27. [PROGRAM CHANGE] / [MACKIE CONTROL] – Pressing this button will enter Program Change
Mode. In this mode, you can send a Program Change or Program Bank Change message to a
hardware or software module. Hold [SHIFT] and press this button to automatically select the Mackie
Control Program.
28. [TEMPO] – When MAX49 is set to Internal Sync, this LED button flashes to indicate the current tempo
of the Arpeggatior and Sequencer. You can tap this button several times to set a new Tempo. If the
Program is reloaded, the Tempo will revert to the last saved Tempo value. (Note: A Program's default
tempo can be set in Edit Mode. Also, this button does not work when MAX49 is set to External sync.)
29. TRANSPORT CONTROL BUTTONS – These five buttons are dedicated buttons for sending transport
control commands. The transport control buttons can be set to transmit either MMC (MIDI Machine
Control), MMC/MIDI SysEx, MIDI START/STOP or pre-assigned MIDI CC values.
Note: You can press the Stop button () three times in quick succession to send an "All Notes Off"
message.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Akai professional MAX49 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Akai professional MAX49 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info