630577
102
Zoom out
Zoom in
Previous page
1/136
Next page
MPC2500 Operators Manual rev 1.0
92
Chapter 14: Mixer
Selecting the pad to apply the effect
With the MPC2500, you can route specific pad(s) to either
of two(2) internal FX. To do this, you need to route the pads
sample in the FX SEND section.
Tips : This picture displays the signal flow of the sample sound to
the stereo out through the effect section. As you can see in this
picture, you can only apply the effects to a pad whose outputs are
set to the stereo out.
You cannot apply the effects to a pads whose outputs
are set to the assignable mix output.
01. In MIXER mode, press the [F3] (FXSEND) key.
The FX SEND page will be displayed.
Each column indicates pad 1 though 16 from the
left to right, and the currently selected pad is high-
lighted. The display at the top indicates the output
setting. The bar display on the bottom indicates the
current send level.
To adjust this level: simply cursor down and use
the DATA wheel.
02. Hit the desired pad.
The column of the selected pad will be highlighted.
03. Press the UP cursor key.
The FX Send field for the effect setting will be se-
lected. You can change the setting by turning the
DATA wheel.
OF No effect will be used.
1
The effect 1 will be used. The Pad sound
will be sent to the FX1 of the effect section.
2
The effect 2 will be used. The Pad sound
will be sent to the FX2 of the effect section.
04. Press the DOWN cursor key and adjust the FXSEND
level by turning the DATA wheel.
Tips : You can also adjust the FXSEND level on the currently
highlighted pad(s) by using the [Q1] (SLIDER).
Mixer Automation
The MPC2500 can record the information such as Level
and Pan changes so that they will automate during se-
quence play back.
01. In the MIXER mode, press the [F4] (SETUP) key.
The SETUP page will be displayed.
02. In the Record mix changes: field, select YES with
the DATA wheel.
If you set this field to YES and change the LEVEL or
PAN in the L/PAN page during the sequence is re-
cording, the changed data will be recorded into the
sequence. The sequence will be played with changing
the Level or the Pan as you did during the recording.
The mixing data recorded in the sequence is dis-
played in STEP EDIT page as follows and you can
edit it same as other MIDI event.
Note : Level event shares with Level of Q-Link.
102


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Akai MPC2500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Akai MPC2500 in the language / languages: English as an attachment in your email.

The manual is 12,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Akai MPC2500

Akai MPC2500 Quick start guide - English, German, French, Italian, Spanish - 74 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info