Manual Aiwa RMD-99ST (page 8 of 80) (English, German, French, Italian, Portuguese, Spanish)

793980

Zoom out

Zoom in

1/80

en 14

USING THE STORED STATIONS

There’s a total of 550 preset memories within the unit. 100 preset memories for each

FM, MW, and LW band, and 250 for SW.

METHOD 1: ATS (AUTO TUNING STORAGE)

1. Fully extend the telescopic

antenna and then press the

FM button to select FM band.

2. Press and hold the FM button,

until the word “PRESET ”

starts ﬂashing on screen on

screen and the frequency

starts advancing; now the

radio will start scanning and

storing all the avalible radio

stations into the memory.

When the frequency stops, it

means that the ATS operation

is already done. Then you can

rotate the TUNING KNOB to

search for those stored stations.

MW/LW ATS:

Press the AM button to select MW/LW band, then follow step 2 of FM ATS.

SW ATS:

Fully extend the telescopic antenna and press the SW ( ) or ( ) buttons to

select SW band.

Modes for SW ATS tuning

A. Using all the meter bands:

Press and hold the ( ) button to ATS the stations within all meter bands.

B. Using the present meter band:

Press and hold the ( ) button to ATS the stations within present meter band.

Notes:

• During ATS process in FM, MW / LW or SW (mode A), pre-stored radio stations will

be replaced automatically by the new searched stations.

• With ATS in SW (mode B), those existing memories will not be replaced; all the

newly found radio stations will be stored in the blank memory addresses.

• If there is too much interference in your surrounding or many mirror/blank stations

are being stored during ATS, you should contract the telescopic antenna (FM and

SW) or rotate the radio for better reception (MW and LW).

USING THE STORED STATIONS

LISTENING TO STORED STATIONS

While operating the Auto Browse Station function, you can simply press on the M

button to store the station into memory to avoid storing unwanted stations and

interfering signals.

Press the VM button to enter the

memory mode, the word “PRESET”

will appear on the screen. Then

rotate the TUNING KNOB to scroll

through the stored stations one

by one.

METHOD 2: STORING STATIONS MANUALLY

METHOD 3: SEMI-AUTO STORING STATIONS

1. Select band and tune to your desired station.

2. Press the M button with the word “PRESET” ﬂashing.

3. Press the M button again to store the station into memory.

Note that you can also wait for 3 seconds to auto store the station into memory.

1. Press the VF button to switch into frequency mode.

2. Press and hold the VF button until “ ” advancing on the screen to auto brow-

se from one station to another.

3. While tuning to your desired station, press the M button followed by “PRESET”

ﬂashing to directly store the station into the next available memory.

The unit will keep on browsing until you deactivate it by pressing on the VF

button again.

1. Press the VM button followed

by “memory page” that

appears in the upper right

corner to enter the memory

mode.

2. Press and hold the VM button

until “PRESET ” flashes to

automatically scan from one

memory to another,

remaining on each station

for approximately 5 seconds.

To stop the automatic search

memory, simply press the VM

button.

METHOD 1: MANUAL MEMORY TUNING

METHOD 2: AUTO BROWSE MEMORY

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Aiwa RMD-99ST in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 9.58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Aiwa RMD-99ST Manual

Product: