29025

Airtronics VG6000 Manual

21
Zoom out
Zoom in
Previous page
1/23
Next page
Page 21
VG6000
THROTTLE CUT ( T-CUT )
After you have landed and taxied back, you can shoot your engine off
by simply pushing a button. The throttle cut feature will do just that.
To set you throttle cut first you must make sure the throttle is working
properly and it will come to a low idle. No more need to use the trim
to shoot your engine off.
To use T-CUT, move the cursor to the T-CUT using the FUNCTION keys. Next use the INC+ or DEC- keys to change the
percentage of throttle cut needed. Throttle cut only works when the stick is in the low position. Make sure the throttle
barrel on your engine will go below the lowest idle position before adjusting throttle cut. Default is “0” setting are from
15 to -15
COUNT DOWN TIMER ( TIMER )
Count down timers help to remind you that it’s time to land meaning lets
get it down before we run out of fuel. If you know how long a normal
flight is on your aircraft “example” 15:00 minutes, you can set the down
timer to sound off at 13:00 minutes. This will give you approximately
2:00 minutes to land with some fuel left over in-case you need to do a
go around. Timer can be set from 0 to 60:00 minutes and are set in
10 seconds intervals.
Example: the left two nubers represent 0~60 minutes and the number
on the right represent 10th’s. 10, 20, 30, 40, 50.
After the timer has reached “0”, it will start to count up. At every minute you will hear 2 beeps.
To set the timer first move the cursor to TIMER using the FUNCTION keys. Number will be flashing 00’0. Use the INC+
key to set the amount of time. Example: timer reads 01’3, this will give you a count down 1 minute 30 seconds.
Pressing the CH/TIMER button will start the count down timer. At the end of the count down you will hear a seies of
beeps starting at the last 10 seconds of the count down.
To stop the timer at anytime simply push the CH/TIMER button. To restart push it again.
To reset the timer simply press both INC+ and DEC- at the same time.
To reset the timer to 00’0 simply press both INC+ and DEC- again. ( 2 times )
… 21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Airtronics VG6000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Airtronics VG6000 in the language / languages: English as an attachment in your email.

The manual is 2,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info