Manual Airpress HK 425-200 (page 29 of 52) (English, German, Dutch, French)

593942

Zoom out

Zoom in

1/52

6.0 MAINTENANCE

Before carrying out any maintenance jobs it is obligatory to stop the

machine and disconnect it from the power mains.

1. After the first 50 operating hours and then every 250 operation hours the oil

should be refreshed. Turn off the oil drain plug (o) and also remove the filler cap

(n). Collect the oil. If the oil does not come out any longer, switch on the drain

plug again and refill the oil (through filler cap) until the oil has reached the correct

level.

Compressor with direct drive: the right oil level is between the two marks on the

dipstick.

Compressor with V-belt drive: has an oil inspection glass on the pump. The oil

level should be between the red dot on the inspection glass and the upper side of

the inspection glass.

Always respect the regulations in force for disposing of old oil!

2. Regularly drain condensation water. The drain tap is situated at the bottom of the

tank (l). Draining with pressure in the tank is the easiest way. Some compressors

have an after cooler with its own drain plug. Also from this device the

condensation water should be drained regularly (is not valid for the H 85).

Condensate must be disposed of in conformity with the local regulations in

force (not in the sewer!).

As an alternative you can place an oil/water separator.

3. The oil level should also be checked regularly. For the right oil level see point 1. If

necessary refill with AIRPRESS compressor oil, order No 36398 (1/2 l) or order

No 36380 (2 l). Checking daily can prevent a lot of troubles!

Use oil of the same type as that already in the machine; do not mix different

types of oil!

4. The air filter element (m) should be cleaned or changed regularly. This change

depends on the amount of fouling and should be done more often in dusty

situations and less often in a clean situation. For cleaning the filter element, take

out the filter container with the filter. Then clean the filter by blowing off the dust.

Only for compressor with V-belt drive:

5. The V-belt should be checked after every 1000 hours. At the right tension, the V-

belt can easily be turned 45 degrees by hand. If tension is too high, strong

corrosion will occur or eventually the spindle of motor or pump may break. At too

little tension, the efficiency of the compressor decreases considerably.

Tightening the V-belt as follows:

Dismount the belt protector (r).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Airpress HK 425-200 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Airpress HK 425-200 Manual

Product: