593942

Airpress HK 425-200 Manual

27
Zoom out
Zoom in
Previous page
1/52
Next page
25
skilled personnel for electric connections.
Before first use first read chapters 3.2 and 4.0.
3.2 AIR CONNECTION
Best use for connection of the compressor to an air circuit a flexible hose, to isolate
vibrations from the machine. The diameter of the hose must meet the connection of
the ball cock. The quick coupling supplied has to be mounted with tape on the outlet
of the reducing valve (on cock (h)).
4.0 FIRST USE
1. Check if the instructions mentioned above have been executed.
2. Check the oil level of the compressor (see chapter 6.0 point 3.). Possibly oil has
been lost during transport. Fill if necessary with AIRPRESS compressor oil.
Avoid the use of extension cables. If you use them, unroll them completely and use
cables of sufficient capacity.
Table for extension cables:
For 230 volt: For 400 volt:
0 - 10 meter: 3 x 1 1/2 mm
2
0 - 25 meter: 4 x 1 1/2 mm
2
10 - 25 meter: 3 x 2 1/2 mm
2
25 - 50 meter: 4 x 2 1/2 mm
2
Compressor with direct drive:
Switch on the compressor by means of the pressure switch (a).
The compressor will now operate, unless the air receiver is still under pressure
(k).
Switch the machine, during operation, exclusively off by means of the button on
the automatic pressure switch (a); the pressure circuit will be vented and the
compressor can start again uncharged.
H 85 without air tank and with 0/1 switch on junction box on the motor.
Compressor with V-belt drive:
Check tension on the V-belt. At the right tension the V-belt (u) can easily be
turned by hand approximately 45 degrees. If necessary, improve tension. See
chapter 6.0 point 5.
Let the compressor run for a short while so you can check if the turning direction
is correct (see arrow on belt protector (r)) (only valid for model 400 V). If the
motor runs in the wrong direction, switch two phases of the electric plug.
Disconnect electricity!
For daily operation of the compressor, see chapter 5.0.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Airpress HK 425-200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Airpress HK 425-200 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info