594047

Airpress 36819 Manual

36
Zoom out
Zoom in
Previous page
1/56
Next page
34
SW1 ON position - it enables the automatic re-start of the compressor in case of
power failure
OFF position - the compressor re-starts only by pressing the START key
SW2 ON position - the compressor re-starts after 3 minutes of low pressure
OFF position - the compressor re-starts after 1 minute of low pressure
SW3 ON position - delayed stop. Press the STOP key: the compressor stops
when the line pressure value is reached. The stop cycle is signalled by the
flashing red led OFF. This function is useful to avoid the risk of the
compressor re-start with the head under pressure. In such case, when
reaching the line pressure value is achieved, the exceeding air is blown off.
OFF position - Immediate stop af ter pressing the STOP key.
Recommended only when the compressor head is equipped with blowing off
valve.
SW4 SW4 switch is in position OFF at the delivery of the compressor.
DO NOT CHANGE THIS SETTING, IN ANV CASE, but, if necessary contact
an Authorized Service Centre.
6. OPERATION AND USE
6.1 Mode of Operation (Tandem models) (Fig. 7)
In order to select the operation cycle, press the STOP button for at least 4 seconds to
activate the different programmes (the corresponding green led wil I light up) at an
interval of 1/2 second. After selecting the desired programme, release the STOP
button. The selected programme will be kept stored in the memory even in case of
power failure.
• Cycle M1-M2: alternated operation of the two pumping units.
SW2 function is active only when this mode is selected, so, depending on your air
consumption, adjust the switch in position ON (Iow consumption) or OFF (high
consumption). When the line pressure value is reached, both the pumping units
stop, then they start again when the pressure value decreases.
• Cycle M1: operation of the sole pumping unit M1.
• Cycle M2: operation of the sole pumping unit M2.
NOTE: If just one unit is used, as usually happens, do not use always the same
unit but Iet the work be shared fairly by both of them.
• Cycle M1+M2: simultaneous operation of the two pumping units.
The first unit M1 starts and after about 10 seconds starts the unit M2; they both
work together and stop when the line pressure value is reached, then they start
again when the pressure value decreases.
NOTE: Please remember to start both units together only if a big amount of
compressed air is needed because under these conditions, and especially at
the start-up, high electrical input peaks may occur.
For the most appropriate operation cycle, contact your usual installer, taking into
account your compressed air consumption and the data written on the EG label of the
compressor.
6.2 Operation cycle
The compressor runs completely automatically by the pressure switch, which stops the
compressor when the max. pressure value is reached and restarts the compressor
only when this value has decreased to the minimum value accepted.
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Airpress 36819 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Airpress 36819 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info