521963
24
Zoom out
Zoom in
Previous page
1/47
Next page
offered by Busse-Yachtshop.com
AIR 403 Land Manual Document #0049 REV D
SOUTHWEST WINDPOWER 8/20/2001 24
3. With the yaw wires connected, the rotor shaft should become more difficult to rotate and
feel “lumpy”. With the yaw wires disconnected it should spin freely. If these conditions do not
exist, you should contact your turbine dealer or Southwest Windpower.
Test 2
1. Remove blade assembly from turbine and place in a safe location. (Do not stand the blade
assembly against a wall.)
2. Connect a voltmeter across the Red and Black yaw wires.
3. With a 5/16” hex drive in an electric drill, spin the rotor shaft while observing the voltmeter.
(Cut a small piece off of the Hex Key provided if necessary.)
4. Rated voltage should be achieved at a minimum of 950 RPM.
NOTE: Do not be alarmed if the open circuit voltage goes above the regulation set point
voltage. The open circuit voltage will not change if you adjust the regulation set point. DO
NOT
adjust the regulation set point in an attempt to alter the open circuit voltage. Changing
the regulation set point will have no affect on the open circuit voltage.
4.3 Performance Test
1. Isolate the turbine from the system.
Connect red positive turbine wire to the battery positive post. Connect the black
negative turbine wire to the negative battery post. Make sure no other system
charging components are connected. Also, make sure that switches, diodes,
regulators or meters are not connected.
2. Connect amp meter.
Connect your non-averaging amp meter in-line the positive (red) wire according to
the manufacturer’s recommendations.
3. Monitor wind speed vs. output
Record the data and compare to the power curve. Use an anemometer located within
5 feet (1.5 m) of the turbine to get accurate wind speed information. An anemometer
located in a higher location will not provide correct information for power curve
assessment. Also refer to the elevation vs. output chart in Section 5.3 on Page 24 for
information on elevations effect on output. Small differences in the wind can have
substantial effects on output.
4. Check results
If the turbine has very poor or no output when compared to power curve, refer to the
Trouble Shooting section.
4.4 Adjusting the Internal Regulator
It is important to understand how to use the AIR 403’s internal electronics to ensure proper
charging of your batteries. Refer to Figure 7 on page 17 for the location of the regulator
adjusting screw. In the following paragraphs 24-volt settings are in Italics.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Air Marine Air 403 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Air Marine Air 403 in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info