464364
27
Zoom out
Zoom in
Previous page
1/70
Next page
29
English
L1
N
L1
X1
3/N/PE ~ 50 Hz 400 V
1
L2L3123
L2L3
2
L1
L1
X1
3/N/PE ~ 50 Hz 400 V
L2L3123
Nenn
L2L3N
3
L1
L1
X1
3/N/PE ~ 50 Hz 400 V
L2L3123
L2L3N
4
L1
L1
X1
3/PE ~ 50 Hz 400 V
L2L3123
L2L3
L1
N
L1
X1
1/N/PE ~ 50 Hz 230 V
5
L2L3123
100 % P
Nenn
2kW
2.2.3 Electronic Charging Control Unit
Behaviour in case of fault
The charging control unit in the device is set at the factory to ”positive fault behaviour (80 % PS),
i.e. in the case of a defective charging control unit (e.g. failure of the control signal), the unit is
fully charged.
The unit can be switched to ”negative fault behaviour” (no charging of the storage heater) by
moving the plug-in bridge X16 to position ”80 % NS” when the device is connected to a digital
charging control unit.
Operation with the charging control unit
The appropriate notes in the operating and installation instructions of the charging control unit
must be observed.
Control signal
The electronic charging control unit can be connected to different control signals (ED) of control
units and can therefore be integrated in existing systems.
It is factory set to an AC control signal (AC voltage signal at terminals A1/A2) with 80 % ED.
By moving the plug-in bridge X16, other ED signals (68/72 %, 37/40 %) can be selected. This is
necessary when the unit is integrated in an already existing system which controls the charging
with one of the named ED signals.
Connection to DC control signal (X3) (see circuit diagram page 19)
If a charging control unit with DC control signal (DC voltage 0.91 V-1.43 V) is installed in the
system, the control signal must be connected to the control terminals covered at the factory
”DC +” (plus pole) and ”DC-” (minus pole) (Pay attention to polarity!).
The 230 V AC control signal may not be connected to the ”DC +” and ”DC –” terminals. The
charging control unit would otherwise be destroyed.
Connection variants
Connection variants
Model
WSP 1210 F
WSP 1810 F
WSP 2410 F
WSP 3010 F
WSP 3610 F
WSP 4210 F
WSP 4810 F
100 %
1.2
1.8
2.4
3.0
3.6
4.2
4.8
91.6 %
1.1
1.65
2.2
2.75
3.3
3.85
4.4
83.3 %
1.0
1.5
2.0
2.5
3.0
3.5
4.0
75 %
0.9
1.35
1.8
2.25
2.7
3.15
3.6
100 %
1.2
1.8
I
80 % PS
II
80 % NS
III
68/72 %
IV
37/40 %
X15 X14
X13
X12 X11
X10
%PS
%
PS
X17
X16
V4
A1
8h heating elements
For the Fitter
100 % P
rated
(series wiring)
91.6 % P
rated
83.3 % P
rated
75 % P
rated
100 % P
rated
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG WSP 3610 F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG WSP 3610 F in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info