Manual AEG WSP 3010 (page 26 of 62) (English, German, Dutch, French)

464353

Zoom out

Zoom in

1/62

For the Fitter

2.5.1 Unit Installation (fig. 3-6)

• Press the air inlet grille (6) down slightly on both sides, tip forward at the front and remove.

Unscrew both screws at the air outlet grille (5) and remove the grille (fig. 3).

• Loosen the front wall (4) with 2 screws at the bottom (inside threaded holes), lift the front wall

slightly and remove (fig. 4). Loosen the inside front wall with 2 screws at the bottom and remove

(fig. 5).

• Disassembly of the right side wall (3): Remove the rotary knob (a), screw (b) on the side wall (3),

pull the side wall slightly to the side at the back (c), push forward, tilt to the side at the top (d),

lift and remove (fig. 6).

• Feed the power cables and connecting cables for charging control unit and discharge control

unit through the opening in the unit rear wall (15) and connect according to section 2.5.2 (lay

connecting cable about 210 mm and shorten as required so that it does not obstruct the air

vents in the side wall);

• Place the unit at the planned location and screw to the wall (or to the floor if floor fixing is

necessary).

• Remove cover plate (10), cardboard inlays and operating button from inside (fig. 9). This must be

completely free of foreign bodies such as packing leftovers.

Check the thermal insulation in the unit for transportation damage and replace if necessary.

Insert the storage blocks (fig. 10 and 11)

The storage blocks are delivered packed separately.

Storage blocks with slight transportation damage may still be used. This does not impair the

function of the heater.

The heating elements (17) must be lifted slightly to insert the storage blocks (9) (fig. 10).

Place the first storage block with the heating element recess at the top some distance away from

the right thermal insulation under the heater and push to the right and rear thermal insulation.

The elongated holes form the heating channels.

When lifting the heating elements, make sure that the through holes in the side thermal insulation

are not widened by the heating elements.

Then push the cover plate (10) removed from the interior over the top storage blocks (fig. 12).

2.5.2 Electrical Connection

The heating elements are connected electrically with 3/N/PE ~ 50 Hz 400 V or in the

units WSP 2010 also with 1/N/PE ~ 50 Hz 230 V.

Direct connection with NYM is possible. The number of supply cables and wires as well as cable

cross sections depends on the connection rating of the unit and the type of mains connection and

on special electricity supply company regulations. Observe the appropriate circuit diagrams for

this.

When connecting the unit to an automatic charging control unit, voltages may occur at the

terminals A1/Z1 and A2/Z2 even when the fuses are removed.

Connection

Relieve the strain on the electrical connecting leads as required and connect according to the

electrical circuit diagram in the device (on the inside of the right side panel) or the connection

diagram.

If the bracket in the switching area for holding the mains terminals is poorly accessible due to too

small a spacing, it can be swung forward during connection work after loosening the screw (not

removing) in the rear panel.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG WSP 3010 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG WSP 3010 Manual

Product: