464372

AEG WSP 300 H Manual

32
Zoom out
Zoom in
Previous page
1/76
Next page
32
For the Fitter
Fig. 9
Fig. 10
Fig. 11
2.3.6 Installation of heater core and elements
●
Slide the kitchen heater into its recess (move to its
final position) and adjust. If necessary, adjust the
screw feet.
●
Install the storage core bricks so that the openings
in the bricks correspond to those in the floor
insulation and are flush with the step in the front
of the floor insulation (Fig. 9 + 10).
When installing the final layer of bricks, set the
core-cover plate (Pos. 6, Fig. 9) with the edge
pointing downwards and towards the heater rear
and such, that it lies between the storage core and
the top insulation. The cover plate can no longer
be pulled forwards out of the heater.
●
Push the heating element E1 (Fig. 9 + 10) from the
front between the storage bricks as far to the rear
as it can go.
●
Set the insulation from the front firmly between
the ends of the heating elements.
●
Install the inside front panel (Fig. 11): To do this,
first push the panel carefully over the heating
element ends E1 on the left-hand side and then lift
it over the heating element ends on the right-
hand side. Fix the inside panel on the side and top
with 8 screws (Pos. 7).
●
Replace the insulation that has been pushed
outwards by the heating elements. The oval-shaped
insulating washers provided are then pushed over
the ends of the heating elements and twisted so
that they are firmly fixed behind the inside panel.
●
Replace the high-temperature safety cut-out F1
and Thermostat F4 (Fig. 11).
●
The free ends of the safety cut-out F1 cables and
the free N-bridge on the switching plate (page 31)
are to be connected to the heater elements E1
according to the circuit diagram.
Note: Once the storage core has been installed
and the heating elements have been
connected, bend the fan resistance R1
with holding bracket on the switching
plate to a horizontal position.
Make sure that the ends of the heating
elements are not in contact with any
internal wiring.
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG WSP 300 H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG WSP 300 H in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info