135582
70
Zoom out
Zoom in
Previous page
1/80
Next page
6
EN
Note: You may also access the RF OUT CH menu by pressing
and holding
MENU on the remote control for 3 seconds
during power off
until the RF OUT CH menu appears.
Setting the Clock
This VCR incorporates a 24-hour clock. The clock must be set
for the Timer Recording function to operate correctly.
Use the remote control for this procedure.
1) Press
MENU.
2) Press
PLAY/o or STOP/L to select “INITIAL”, then press
F.FWD/B.
3) Press
PLAY/o or STOP/L to select “CLOCK”, then press
F.FWD/B.
4) Press
PLAY/o or STOP/L until the relevant year appears,
then press
F.FWD/B.
5) Press
PLAY/o or STOP/L until the relevant month
appears, then press
F.FWD/B.
6) Press
PLAY/o or STOP/L until the relevant day appears,
then press
F.FWD/B.
7) Press
PLAY/o or STOP/L until the relevant hour appears,
then press
F.FWD/B.
8) Press
PLAY/o or STOP/L until the relevant minute
appears.
9) Press MENU to start the clock.
Note:
•Press REW/s to go one step back from the current step
during steps
5) to 8).
Although seconds are not displayed, they begin counting
from 00 when you exit by pressing
MENU. Use this feature
to synchronize the clock with the correct time.
If the VCR is unplugged or if there is a power failure for
more than 30 seconds, you may have to reset the clock.
Channel Presetting
Tuning of broadcast channels not already preset in the VCR
can be performed in two ways.
Automatic Channel Preset
•ByAUTOMATICALLY tuning channels and placing
them in sequential order in the VCR’s memory i.e. the first
channel found will be memorized into the VCR’s channel
position 1, the second channel found will be memorized
into the VCR’s channel position 2 and so on.
Execution of the “Automaticchannel presetting cancels all
the preset channels. DO NOT use this feature if you intend
to use some of the pre-tuned channels. Use the “Manual
channel presetting function to tune in the additional
channels you require.
Manual Channel Preset
Each channel is tuned manually and individually. Follow
the steps laid out in the “Manual Channel Preset” section.
Before you preset Channel...
It is necessary to set the video channel if your VCR is
connected to the TV via the coaxial cable, and TV channel
36 is set for broadcasting, or interference lines appear on
the picture. Please refer to “Video Channel Setting”.
Automatic Channel Preset
You can programme the tuner to scan only the channels that
you can receive in your area.
Use the remote control for this procedure.
1) Turn on the TV and select the TV channel to the video
channel on the TV.
2) Press
MENU.
3) Press
PLAY/o or STOP/L to select “INITIAL”, then press
F.FWD/B.
4) Press
PLAY/o or STOP/L to select “CH TUNING”, then
press
F.FWD/B.
5) Press
PLAY/o or STOP/L to select “AUTO”, then press
F.FWD/B.
The tuner scans and memorizes all the active channels in
your area. After scanning, the tuner stops on the lowest
memorized channel.
MENU
TIMER
SET UP
INITIAL
RF OUT CH 36
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
CLOCK
YEAR 2 0 0 4
MONTH 0 1
DAY 0 7 WE
HOUR
_ _
MINUTE
_ _
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
CH TUNING
AUTO
MANUAL
MOVE
scanning
MENU
TIMER
SET UP
INITIAL
HG210ED(EN).fm Page 6 Tuesday, March 2, 2004 4:08 PM
70


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG vcr 4505 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG vcr 4505 in the language / languages: German as an attachment in your email.

The manual is 3,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info