Manual AEG ste 500 (page 6 of 82) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Finnish)

382754

Zoom out

Zoom in

1/82

ENGLISH

ST 500, STE 500, STEP 500

The appropriate degree of pendulum effect can be taken from the following chart

and compared with the marking at the pendulum stroke lever.

Material Degree of swing action

Wood I - III

Plastic I

Aluminium 0 - I

Steel 0

Ceramics 0

Rubber 0

The stroke rate shown in the chart is only

a suggestion for your general guidance!

The stroke rate can be set on the stroke

rate control even while the motor is

running.

1. Set the stroke and pendulum stroke according to the material to be cut.

2. Position the machine with the front part of the base plate on the material, and

switch on.

3. Press the machine downwards onto the material and guide it along the cutting line.

Do not press down too hard on the piece you are cutting. Light pressure on the saw

blade is sufficient to achieve the optimum rate of sawing.

When cutting along a score line, use the marking on the anti-splintering device as an

optical guide.

To obtain a perfectly straight cut, clamp a strip of wood as a guide along the material

or use the parallel guide (accessory).

For cutting at an angle, or cutting a bevel, adjust the base plate.

For sawing close to the edge, set the base plate at its rearmost position.

To avoid vibration, clamp metal sheets onto a wooden base.

To saw metal, use cooling agents along the cutting line (oil, white spirit).

Plunge cuts without pre-drilling a hole are possible with soft materials (wood, light

building materials for walls). Harder materials (metals) must first be drilled with a hole

corresponding to the size of the saw blade.

Move the base plate to the rearmost setting in order to obtain the best possible

cutting angle for starting the cut.(see section ”Adjusting the base plate”)

1. Set the pendulum stroke at the pendulum stroke control to “0”.

2. Without switching the machine on, place it with the front edge of the base plate on

the cutting point.

3. Switch the machine on and carefully lower the saw blade already running into the

material.

GERMANY

274315

STEP 500

electronic

III

GERMANY

274315

STEP 500

electronic

III

GERMANY

274315

STEP 500

electronic

III

Advice for

operation

Hints

Sawing sheet

metal

Plunge cuts

III

My jigsaw just when “bang” & blew the house fuse. Having opened it up a component looks blown- white cylinder 2 ohms mark & lots of other numbers& letters - is it repairable??
Steve stevemaylor@sky.com Submitted on 10-2-2020 at 18:11
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG ste 500 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 3,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG ste 500 Manual

Product: