722671

AEG RX9-1 SGM Manual

16
Zoom out
Zoom in
Previous page
1/52
Next page
1616
1x
3x
3x
Troubleshooting
Problem Error
Code
Cause Solution
Wrong time is displayed
on the robot.
The robot has not
received updated time
from the WiFi network.
Make sure the robot is connected to
the WiFi network and wait until it
receives the correct time. If it does
not update within 24 hours redo the
onboarding procedure.
The room is not properly
cleaned, but the robot
returns to the Charging
base.
- The robot is returning
to the Charging base to
charge the batteries.
The robot will automatically
continue the cleaning program as
soon as the batteries are recharged.
Water has been sucked
into the robot.
- - It will be necessary to replace the
motor at an authorized AEG service
centre.
Damage to the motor caused by the
penetration of water is not covered
by the warranty.
Software issue. E:30 Software is not working
correctly.
Please update the robot’s software.
E:31 Software upgrade has
failed.
Please redo software update.
Service needed. E:40 - Contact an authorized AEG
service center.
System error. E:41 Internal error. Please restart desired operation.
E:42
For any further problems, please check the service area in the APP or on our website.
Problem Error
Code
Cause Solution
The display is blank. - The battery is empty. Charge the battery.
The robot does not start.
The Dust container is
not present or properly
closed.
Place the Dust container in the
robot, properly close the lid.
(x3)
The robot is lifted. Place the robot on the oor before
starting.
The robot does not
move/clean properly.
E:10 The bumper is stuck. Please make sure the bumper can
move properly and remove any
debris that might block it.
E:11
Right wheel is stuck.
Check that all parts turn freely.
Clean and remove entangled
threads from parts if needed.
Replace Brush roll or Side brush if
damaged.
Check ”Cleaning and maintenance”
page 14
E:12 Left wheel is stuck.
E:13 Brush roll is stuck.
E:14 Side brush is stuck.
E:15 The robot is stuck or
unable to navigate.
Lift and place the robot where it
can move freely. Check ”Tips on how
to get the best results” page 12.
E:16 The 3D Vision System is
blocked or dusty.
Clean the 3D Vision System and
make sure nothing is blocking
the sight. Check ”Cleaning and
maintenance” page 14.
The Dust container is
full or blocked.
Empty and/or clean the Dust
Container. Check ”Emptying the Dust
container” page 13.
E:17
The robot is opperating
on a surface which is too
slippery.
Move the robot and charger to a
new location and start again.
No charge indication. - The power cord and
adapter is not properly
assembled, and/or
connected to the mains.
Connect the adapter connector to
the Charging base. Connect the
power cable to the mains. Make
sure the Charging plates on the
robot and the Charging base are
connected.
Check that the plug and cable are
not damaged.
The Charging plates
on the robot and the
Charging base are not
connected.
The batteries runs
empty fast
- The batteries life has
expired.
Change the 2 battery packs.
Check “Changing the batteries” page
15.
Battery related
problems
E:20 Incorrect Charging base
is used.
Only use the original AEG
Charging base, supplied with the
robot. If the Charging base needs to
be replaced; use AEG Charging base
(ANC: 406000071).
E:21 Batteries are
malfunctioning during
use.
Change the 2 battery packs.
Check “Changing the batteries” page
15.
E:22 Product temperature is
too high.
Let the robot paused outside the
charging station for 6 hours.
E:23 Batteries are not
properly connected to
the robot.
Connect batteries to robot. Check
“Changing batteries” page 15.
The time is not
displayed.
The current time is
not set.
When the robot is connected to WiFi
the time will automatically set.
Troubleshooting
Consumables & Accessories
www.aeg.com/shop
RX9 Performance kit
Ref: ARK2
PNC: 9001681858
Battery pack
ANC: 406000060
Charging base
ANC: 406000071
RX9 Power brush
REF: ARSB2
PNC: 9001681197
4x
RX9_Osiris_AEG.indd 16 2017-05-24 15:26:26
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG RX9-1 SGM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG RX9-1 SGM in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 12,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info