Manual AEG RTi 101 EP (page 11 of 28) (English, German, Dutch, French)

464368

Zoom out

Zoom in

1/28

For the Fitter

2. Installation instructions

The room temperature regulator must be fitted by an authorised specialist under consideration

of these operation and installation instructions and the operating and installation instructions

of the storage heater.

All electrical connection and installation work must be performed in accordance with the VDE

regulations 0100, the regulations of the electricity supply company responsible and the pertinent

national and regional regulations.

2.1 Technical Data

2.2 Packing Unit

1 Room temperature regulator with four spacers and

- potentiometer with connecting lead

– 6-pole connector with cable harness

1 ON/OFF switch with 2 wires (length 500 mm)

1 temperature selector knob

1 Operating and installation instructions

1 separate double wire (length 500/650 mm)*

1 separate wire with distributor (length 150 mm)*

1 circuit diagram label

1 control panel label

2 cable straps

2 cable twisters

* only needed in connection with ZH 1004 to ZH 1017

2.3 Installation

Disconnect the storage heater from the power supply before starting installation work.

When connecting the storage heater to an automatic charging control unit, there may be

voltage at the terminals A1/Z1 – A2/Z2 even when the fuses are removed.

When installing several storage heaters in a row make sure that the room temperature controller is

installed in the outside right unit. This guarantees that the room temperature can be measured

properly.

2.3.1 Order of Installation

• Remove air outlet and inlet grille, front wall and right side wall as described in the storage

heater operation and installation instructions;

• Press the dummy caps (1) for the switch and temperature selector knob out of the control panel

at the top and bottom left from the switching area side using a suitable tool (fig. 1).

• Installation of the ON/OFF switch:

Push both wires through the cut-out in the metal bracket and snap onto the metal bracket (4)

with the holder (fig. 2).

Press the on/off switch (2) into the holder with the symbol "I" at the right. Push the wires

through the long, oval opening of the angle plate on which the socket strip is mounted from rear

to front and clamp the wires arranged at the centre of the switch to the top terminal strip X2

(LE') and the outside wire to the bottom terminal strip X1 (L) (see page 15 in the circuit diagram).

• Fix the potentiometer (5) with plugged on 3-wire connecting lead from the switching area side

to the angle plate (4) with a screw 4 x 10 mm. It should be noted here that the rotary axis of the

potentiometer is turned to the left (anti-clockwise) and the flat side of the rotary axis is facing

to the right (fig. 3).

• Lay the 3-wire connecting lead of the potentiometer along the back of the angle plate to the

discharge control unit slot. To do this, pull off the 3-pin plug from the potentiometer, lay the

cable and replace the 3-pin plug.

Model

Rated voltage

Connection rating

Control rating fan

RTi 101 EP

1/N/PE ~ 50 Hz 230 V

16 A with supplementary heater

100 VA

English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG RTi 101 EP in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG RTi 101 EP Manual

Product: