463172
9
Zoom out
Zoom in
Previous page
1/111
Next page
16 17
MAINTENANCE
Infrequent Lubrication as Required
Apply automotive type oil directly on slide tubes. It will
be picked up and dispersed by built in felt wicks.
Apply a light oil or a pressurized light spray oil to the
arm pivot shaft (47).
Apply a light oil or a pressurized light spray oil to the
torsion spring (46) as shown.
Apply a light oil or a pressurized light spray oil to the
lower guard spacer (44), roller (45) and cover plate (3)
as shown.
MOTOR BELT TENSION (FIG. 26)
The motor belt tension was properly adjusted at the
factory. However, to check the belt tension:
Use a Phillips screwdriver to remove the five screws
holding the belt cover and remove the cover.
To check the belt tension squeeze the belt. Using light
pressure the belt should deflect approximately
25.4 mm.
To adjust the tension:
-Use a Phillips screwdriver to loosen(but do not
remove) the six motormount screws.
-To increase the belt tension turn the adjusting
socket head set screw clockwise. To decrease the
tension turn the adjusting set screw counter-
clockwise.
Note: Excessive belt tension will cause the motor to
fail prematurely.
-Securely tighten the six motormount screws.
Replace the belt cover.
TROUBLESHOOTING GUIDE
General
Problem Probable Cause Suggested Corrective Action
Blade hits table 1. Misalignment 1. Get authorized Service
Angle of cut not accurate 1. Misalignment 1. See “Alignment” section
Can’t move miter adjustment 1. Sawdust under table 1. Vacuum or blow out dust
Wear Eye Protection
Power head wobbles 1. Loose pivot points 1. See Bevel Pivot Adjustment
in “Alignment” section
Power head won’t fully rise 1. Lubrication needed 1. See “Lubrication” section
or blade guard won’t fully close 2. Part failure 2. Get authorized Service
3. Pivot spring or guard spring 3. Get authorized Service
not replaced properly after service
4. Sawdust sticking to stops 4. Inspect/clean stops
Blade binds, jams, burns wood 1. Improper operation 1. See “Basic Saw Operation” section
Rough cuts 2. Dull blade 2. Replace or sharpen blade
3. Improper blade 3. Replace with 305mm diameter blade
designed for the material being cut
4. Bent blade – check flatness 4. Replace blade
across expansion slots on blade
Tool vibrates or shakes 1. Sawblade not round 1. Replace blade
2. Sawblade damaged 2. Replace blade
3. Sawblade loose 3. Tighten arbor screw
4. Other 4. Get authorized Service
Power head hard to 1. Lube needed 1. See - “Lubrication” section
pull/push down
ENGLISH ENGLISH
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG PS 305 DG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG PS 305 DG in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info