551733
11
Zoom out
Zoom in
Previous page
1/16
Next page
11
Place the power unit in order to make the exhaust pipe
as short as possible. Exhausts should be limited to no longer
than 5 meters.
• Keep in mind that you may need space on the sides of your
central unit to be able to access the dirt receptacle.
Refer to page 14 - Image 6
• Align the power unit intake fi tting to the main trunk line projecting
from the wall.
DO NOT GLUE. Attach the exhaust pipe to
the motor exhaust if exhausting outdoors. Make sure the exhaust
pipe is as short as possible.
NOTE: Mount central power unit at least 30cm from the ceiling
and any adjacent wall, at least 70cm from the fl oor and within 1.8 m
of an electrical outlet. Review any local regulations that may apply.
Refer to page 14 - Image 2
WARNING
Do not block the hood ventilation openings on the top of the central
power unit. Lack of ventilation will cause the motor to overheat.
WARNING
Do not locate the central power unit in a high temperature area where
it is inaccessible for example, an attic or crawl space.
For the ultimate in air control you have the a true HEPA fi lter and may
be included with your choice of power unit or can be purchased from
an authorized dealer/distributor. Simply attach the true HEPA fi lter as
shown.
Refer to page 14 - Image 7
SYSTEM TEST
Be certain to comply with local electrical codes and regulations.
Plug the unit into a regular electrical outlet. You are now ready to
check the installation of the unit:
• Be sure the fi lter is properly installed in the power unit.
• Be sure the dirt receptacle is properly secured to the power unit.
• Plug the hose into each inlet valve to be sure the electrical
contacts operate properly.
• Check each inlet valve for air leaks.
• Check each pipe connection for air leaks.
Refer to page 14 - Image 8
HOW TO USE CENTRAL VACUUM SYSTEM
Your central vacuum system is controlled by a switch on your
hose. Simply insert the hose into the valve and turn the switch to
the on position. This will start the power unit and the fl ow of air.
When you are fi nished, turn the switch on the hose to the
off position and remove the hose from the inlet valve. When
unplugging the hose, hold the inlet cover open for a few
seconds to allow suction to decrease thus, protecting the
inlet valve seal.
Refer to page 14 - Image 8
LED INDICATIONS - OPTIONAL DEPENDING ON MODEL
You machine may be equipped with some or all of the indicators
listed below.
Refer to page 14 - Image 9
On/Off Motor Fault Dirt Receptacle Full Reset
Your power unit is equipped with a multi color LED panel. This LED
panel will provide you with necessary information on your power unit’s
performance, maintenance and diagnostics. Below are descriptions
of the different messages the power unit will provide.
NORMAL OPERATION
When the power unit is OFF and considered to be in standby mode
the LED button will be RED.
When the power unit is ON and in use the LED will be GREEN.
When the motor fault light is ON see further description below.
When the dirt receptacle light is ON, empty dirt receptacle, press the
RESET button and hold for 10 seconds.
MOTOR FAULT
In the case of a blown fuse or disconnected motor wire and the
power unit is not functioning the ON/OFF button will be constantly
GREEN In the case of an over current shutdown, the ON/OFF
button will be fl ashing RED, the GREEN light will on and off rapidly
and the MOTOR FAULT light will be AMBER and turn on and off
rapidly. This fault will reset automatically in 15 seconds if the low volt
connection is OFF at the hose.
In the case of a continued over current and the low volt connection
is ON and the hose the ON/OFF button will constantly be RED,
the GREEN light will fl ash slowly and the MOTOR FAULT will slowly
ash AMBER.
In the unlikely event of a bad frequency received by the power unit
the power unit will not start and the ON/OFF button will remain
constantly RED. In the case of a high line voltage received by
the power unit the ON/OFF button will alternate between RED
and GREEN three times- pause briefl y – alternate between RED and
GREEN three times – long pause- and then repeat. This will
continue until the line voltage returns to the correct level.
LCD SCREEN - OPTIONAL
Refer to page 14 - Image 8
In the main screen of the LCD, the AEG-Electrolux logo will appear.
This logo may scroll from side to side to avoid the image ingraining
itself onto the LCD Display. You will see the logo when the power
unit is not in use.
The button that best lines up with the Power symbol on the screen
can be used to activate the unit. Press this button to toggle the unit
on/off. The unit may also be activated from any installed inlet.
When you LCD power unit is in standby mode the four white lights on
your LCD unit will light up in sequence and alternate moving from left
to right then reversing right to left. This pattern will repeat continuously
and is an indication that your power unit is ready for use and
functioning properly.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG Oxygen - K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG Oxygen - K in the language / languages: English, German as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AEG Oxygen - K

AEG Oxygen - K Installation Guide - English - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info