515890
36
Zoom out
Zoom in
Previous page
1/164
Next page
37 GB
j Check whether the vehicle has a 16-pole
OBD II socket. Check the vehicle emission
control label (VECI Label) to see if your
vehicle can be diagnosed.
j The OBD II socket is located in the area of
the fuse box below the dashboard in most
vehicles. Should you not find the OBD II–
socket, please see the vehicle manual or ask
your vehicle manufacturer.
j The AEG OBD II diagnostic device OL 8000
works with all vehicles and small vans built
as from 2000 with petrol engines and 2003
with diesel engines, which are equipped with
OBD II-socket and contain the following
diagnostic protocols: VPW, CAN, PWM, ISO
9141 and KWP2000.
j The AEG OBD II diagnostic device OL 8000
reads and deletes general and manufacturer
specific diagnosed error codes (DTC’s) out of
the engine control device
j Vehicles built as from 2002 which are support-
ed with the mode 9, the VIN (Vehicle Identi-
fication Number) of the vehicle is read out.
j With this device, the status of the malfunc-
tion warning light (MIL) can be deleted. In
addition the emission-display status can be
monitored.
j For this device a separate power supply is
not required. The power supply and data
transfer follows via the connection cable in
combination with the on-board computer of
the vehicle.
Read out error codes
IMPORTANT NOTE! Switch of the vehicle be-
fore error diagnosis. The OBD II device must not
be connected while the engine is still running or
the ignition is still switched on.
Start error diagnosis
1. Switch of the ignition of the vehicle
2. Connect the OBD II connection plug
4
with
the OBD II connection socket of the vehicle.
3. Wait a short moment until the device is
ready for operation and »AUTOSCAN
8400« is displayed in the LC-Display
1
.
4. Now switch on the ignition but do not start
the engine! If the LC-display
1
shows an
»ERROR« message, switch of the ignition of
the vehicle and wait for approx. 20 seconds
DTC Example
P 0 2 0 2
System
B = Body
C = Suspension
P = Propulsion system
U = Network
Code type
0 = General
1 = Manufacturer-
specific
Sub-System
1 = Fuel / Air /
lambda sensor
2 = Air inlet- and
pressure system
3 = Ignition, misfire
control
4 = Emissions- and
exhaust control
5 = Speed – and bra-
ke control system
6 = Engine manage-
ment / Board
computer
7 = Gear box / Hyd-
raulic sensors
8 = Gear box /
Hydraulic pressu-
re
9 = Automatic gear
The error code shows
which component is
damaged.
Start-up / Operation
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG OBD II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG OBD II in the language / languages: English, German, French as an attachment in your email.

The manual is 5,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AEG OBD II

AEG OBD II User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info