648443
14
Zoom out
Zoom in
Previous page
1/36
Next page
14
Installation - for contractors
8. Appliance description
8.1 Appliance layout
26_07_30_0004
1
3
2
4
1 Natural stone panel
2 Wall mounting brackets with xing screws
3 Power cable
4 Spacer studs
Note
The hexagon screws for wall mounting are not inclu-
ded in the standard delivery.
A heating conductor, featuring 2 safety temperature limi-
ters with automatic reset, is laid in a duct system milled
into the back of the natural stone panels. The duct system
is then lled with marble adhesive which acts as a cover.
8.2 Standard delivery
The following are delivered with the appliance:
3 Wall mounting brackets with xing screws
1 Spacer stud
NSH 35-115: 1 Reector panel
NSH 145-165: 2 Reector panels
8.3 Special accessories
The natural stone heater is controlled via the room tem-
perature controller.
RT 600: Room temperature controller with thermal
feedback, breaking capacity 10 A / 230 V
RT 601 SN: Room temperature controller with ther-
mal feedback, with ON/OFF switch, breaking capaci-
ty 10 A / 230 V, installation on nished walls
RT 5050 SN: Room temperature controller with ther-
mal feedback, with ON/OFF switch, breaking capaci-
ty 10 A / 230 V, installation on unnished walls
RTE 900 SN: Electronic 2-point controller with ON/
OFF switch, breaking capacity 16 A / 230 V, installa-
tion on nished walls
RTE 5050 SN: Electronic 2-point controller with ON/
OFF switch, breaking capacity 16 A / 230 V, installa-
tion on unnished walls
RTF: Digital, wireless room temperature controller
with 7-day program, 5 available operating modes
9. Preparations
9.1 Installation site
The natural stone heater is intended solely for permanent
wall mounting. Ensure the wall offers adequate load-be-
aring capacity.
It can be installed in any room. In bathrooms, the natural
stone heater can be mounted in safety zone 2 (not the
mains junction box).
9.2 Aligning the appliance
The natural stone heater is congured at the factory for
horizontal installation.
If you want to install it vertically, make the following chan-
ges before beginning installation:
» Replace the wall mounting bracket above the power
cable with the diagonally positioned spacer stud.
WARNING Electrocution
Ensure that the power cable is always located at the
lower edge.
» Rotate both wall mounting brackets with the slot
apertures downwards.
!
Material losses
Carefully tighten the xing screws in the natural
stone heater, as otherwise the rawl plugs in the na-
tural stone panel may over-rotate and become loose.
9.3 Mounting the reector panel
Depending on size, the appliance is delivered with 1-2 re-
ector panels made from aluminium-coated EPS. Reec-
tor panels have insulating as well as reecting properties
and reduce heat loss through the wall.
If you are installing your appliance on an external wall, we
recommend mounting the reector panel at the installati-
on site before tting the appliance.
Note
The aluminium coating of the reector panel will rub
off slightly.
» Wear protective gloves when mounting the re-
ector panel.
» Use a suitable adhesive (wall adhesive) and a not-
ched trowel with medium sized notches (B2 or B3)
for mounting the reector panel.
» Apply the adhesive to the entire rear surface of the
reector panel.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG NSH 165 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG NSH 165 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info