Manual AEG MBS 30 Turbo (page 23 of 130) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

463137

Zoom out

Zoom in

1/130

Lower guard function

Check lower guard for proper closing before each use. Do

not operate the saw if lower guard does not move freely and

close instantly. Never clamp or tie the lower guard into the

open position. If saw is accidentally dropped, lower guard may be

bent. Raise the lower guard with the retracting handle and make sure

it moves freely and does not touch the blade or any other part, in all

angles and depths of cut.

Check the operation of the lower guard spring. If the guard

and the spring are not operating properly, they must be

serviced before use. Lower guard may operate sluggishly due to

damaged parts, gummy deposits, or a build-up of debris.

Lower guard should be retracted manually only for special

cuts such as „plunge cuts“ and „compound cuts.“ Raise lower

guard by retracting handle and as soon as blade enters the

material, the lower guard must be released. For all other

sawing, the lower guard should operate automatically.

Always observe that the lower guard is covering the blade

before placing saw down on bench or oor. An unprotected,

coasting blade will cause the saw to walk backwards, cutting

whatever is in its path. Be aware of the time it takes for the blade to

stop after switch is released.

Please do not use abrasion disks in this machine!

SAFETY INSTRUCTIONS WHEN WORKING

WITH DIAMOND CUTOFF WHEELS

Read all safety warnings, instructions, illustrations and

specications provided with this power tool. Failure to follow

all instructions listed below may result in electric shock, re and/or

serious injury.

Always use guard provided with the tool. The guard must

be securely attached to the power tool and positioned for

maximum safety, so the least amount of wheel is exposed

towards the operator. Position yourself and bystanders away

from the plane of the rotating wheel. The guard helps to protect

operator from broken wheel fragments and accidental contact with

wheel.

Use only diamond cut-o wheels for your power tool. Just

because an accessory can be attached to your power tool, it does not

assure safe operation.

The rated speed of the accessory must be at least equal to the

maximum speed marked on the power tool. Accessories running

faster than their rated speed can break and y apart.

Wheels must be used only for recommended applications. For

example: do not grind with the side of cut-o wheel. Abrasive

cuto wheels are intended for peripheral grinding, side forces applied

to these wheels may cause them to shatter.

Always use undamaged wheel anges that are of correct

diameter for your selected wheel. Proper wheel anges support

the wheel thus reducing the possibility of wheel breakage.

The outside diameter and the thickness of your accessory

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately guarded or

controlled.

Always use blades with correct size and shape (diamond

versus round) of arbour holes.

Blades that do not match the

mounting hardware of the saw will run eccentrically, causing loss of

control.

Never use damaged or incorrect blade washers or bolt. The

blade washers and bolt were specially designed for your saw, for

optimum performance and safety of operation.

Causes and operator prevention of kickback:

kickback is a sudden reaction to a pinched, bound or misaligned saw

blade, causing an uncontrolled saw to lift up and out of the workpiece

toward the operator;

when the blade is pinched or bound tightly by the kerf closing down,

the blade stalls and the motor reaction drives the unit rapidly back

toward the operator;

if the blade becomes twisted or misaligned in the cut, the teeth at

the back edge of the blade can dig into the top surface of the wood

causing the blade to climb out of the kerf and jump back toward the

operator.

Kickback is the result of saw misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below.

Maintain a rm grip with both hands on the saw and position

your arms to resist kickback forces. Position your body to

either side of the blade, but not in line with the blade.

Kickback could cause the saw to jump backwards, but kickback forces

can be controlled by the operator, if proper precautions are taken.

When blade is binding, or when interrupting a cut for any

reason, release the trigger and hold the saw motionless in

the material until the blade comes to a complete stop. Never

attempt to remove the saw from the work or pull the saw

backward while the blade is in motion or kickback may occur.

Investigate and take corrective actions to eliminate the cause of blade

binding.

When restarting a saw in the workpiece, centre the saw blade

in the kerf and check that saw teeth are not engaged into the

material. If saw blade is binding, it may walk up or kickback from

the workpiece as the saw is restarted.

Support large panels to minimise the risk of blade pinching

and kickback. Large panels tend to sag under their own weight.

Supports must be placed under the panel on both sides, near the line

of cut and near the edge of the panel.

Do not use dull or damaged blades. Unsharpened or improperly

set blades produce narrow kerf causing excessive friction, blade

binding and kickback.

Blade depth and bevel adjusting locking levers must be tight

and secure before making cut. If blade adjustment shifts while

cutting, it may cause binding and kickback.

Use extra caution when making a „plunge cut“ into existing

walls or other blind areas. The protruding blade may cut objects

that can cause kickback.

English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG MBS 30 Turbo in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG MBS 30 Turbo Manual

Product: