546483

AEG KRC 4361 BT Manual

35
Zoom out
Zoom in
Previous page
1/62
Next page
English
35
• Fortheinstallationthecupboardmustfullthefollowing
conditions:
Thickness of the cupboard floor
between 16 mm and 20 mm.
• Thewallmountingofthecupboardmustbestableand
anchored firmly in the wall with at least 2 screws.
• Important! Do not install the device above a cooker!
• Wheninstallingthedeviceitmustbeensuredthatthere
is a power socket within reach.
• Themainssocketmustbewithineasyreach,sothatthe
plug can be quickly removed in an emergency.
• Important! Do not connect the device to the mains
power supply until after installation!
• Thedevicecannotbeinstalledundercupboardsunder
which there is a lighting strip.
• Formounting,youmayneedthefollowingsupplies:A
drill with 6 mm drill bit, pilot drill or nail, Allen key, tape
measure, adhesive tape, scissors, safety goggles.
Supplied mounting accessories
4 Screws
4 Spacers
1 Drilling template
CAUTION:
• Pleaseadheretothedimensionsstatedintheinstalla-
tion instructions.
• Youshoulduseonlytheinstallationaccessoriessup-
plied.
Installation
1. Tape the template firmly down to the shelf with adhesive
tape. With the help of a gimlet or nail pierce the crosses
at the attachment points and use it to mark the holes.
2. Remove the template and drill the holes into the wall
cupboard.
3. Insert the spacer into the holes provided on the device.
NOTE:
Sufficient ventilation is only guaranteed with a spacer.
4. Countersink the screws into the holes in the cupboard.
5. Using the 4 screws and the spacers, attach the kitchen
radio to the bottom of the cupboard.
6. Tighten the screws hand-tight with an Allen wrench.
CAUTION:
Use an Allen wrench and not an electric screwdriver.
Start-up of the device / Introduction
• Makesurethatthedeviceisadequatelyventilated!
• Ifapplicable,removetheprotectivelmfromthedisplay.
Power supply
Please ensure that the mains voltage corresponds to the
information on the type plate. Plug the power plug into a
properly installed socket.
Inserting the power reserve battery
(Battery not included in scope of delivery)
During a power outage, or when the power plug is pulled
from the socket, the clock time and the alarm times will be
lost. To prevent this, insert a power reserve battery as follows.
1. Open the battery compartment on the bottom. Turn the
battery compartment lid in the direction “OPEN”.
2. Insert a button cell battery of the type CR 2025 3 V. Ensure
the correct polarity (see battery compartment lid)!
3. Close the battery compartment again.
WARNING:
Thebatteriesshallnotbeexposedtoexcessiveheatsuch
as sunshine, fire or the like. Danger of explosion!
CAUTION:
• Batteriesmayleakoutandlosebatteryacid.Ifthe
device is not used for a longer period of time, remove
the battery.
• Batteriesdonotbelonginthehouseholdwaste.
Dispose of spent batteries at the designated collection
points or at the dealer.
Switching the Device on/off (10)
• Turnonthedevicebypressingthe
/FUNC button.
• Toturnoffthedevice,keepthe /FUNC button pressed
for about 3 seconds.
NOTE:
After about 30 minutes without signal, or if the signal is too
low, the device will switch to Standby automatically.
Selecting the operating mode (10)
When the device is turned off, you can switch between
radio and Bluetooth mode by pressing the
/FUNC. button
repeatedly.
Setting of the Clock (24 h)
1. Hold down the TIME SET/COOK TIMER button (14) for
approx.3seconds.Thenotication“24H”willappearin
the display.
2. Select the time format with the SKIP+/SKIP- buttons (7/8).
NOTE:
“PM” will show in the display in the afternoon with the
12-hour indication.
3. Press the TIME SET/COOK TIMER button to confirm.
The hour setting will blink in the display.
4. Adjust the setting with the SKIP+/SKIP- buttons (7/8).
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG KRC 4361 BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG KRC 4361 BT in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 5,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info