Manual AEG DBS 5533 (page 31 of 54) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

458667

Zoom out

Zoom in

1/54

English

CAUTION: INITIAL USE:

Please proceed as follows:

• The tank should only be  lled up to the maximum

mark. Do not over ll!

• Close the water tank.

• Connect the base station to a 230 V / 50 Hz socket

with earthing contact.

• Turn the switch (4) on the base on.

• Set the desired temperature within the range „• •“

to „• • •“.

• Please wait until the control lamp (6) on the base

lights up.

• Now press the steam jet button (11) for at least 1

minute or use the bar (12) to lock the steam jet

button in place.

ޥ NOTE:

• This time is needed for the steam to reach the

iron.

• Keep a cloth ready! During this phase water

also comes out of the soleplate of the iron.

• When only steam comes out without any water

you can stop the procedure. Then press the steam

jet button another 2-3 times without touching the

clothes that are to be ironed.

• After you have ironed an old but clean cloth a few

times, your station is ready for use.

ޥ NOTE: on Steam Ironing:

• While the pump is active do not press the steam jet

button (11).

• If you have been using the permanent steam func-

tion, release the bar (12).

• Wait until the control lamp (6) goes on again,

otherwise water can leak out of the soleplate of the

iron.

Vertical Steam

This can be used to produce a jet of steam in a vertical

direction.

Hang your laundry on a clothes hanger and move the

iron to approximately 2-3

cm away.

How can I replenish the water during operation?

Re ll with water before the tank is completely empty.

The lamp (5) shows that there is not enough water.

• If you have been using the permanent steam func-

tion, release the bar (12).

• Set the temperature control to „0“.

• Turn the switch (4) on the base o .

• Remove the mains plug from the socket.

• Remove the iron and the iron rest (7) and put both to

one side.

ޥ NOTE:

You should only touch the rest by the side handles (10)

or use an oven cloth. The surface warms up according

to how long you iron.

• In order to  ll the water tank, push the lock (9) open

and use the funnel supplied.

• Fill the tank up to the maximum mark. Do not over-

 ll!

• Close the water tank.

• Continue ironing.

ޥ NOTE:

Keep a cloth ready! At  rst water may also be expelled

from the soleplate of the iron.

When you have  nished

• Now you can start ironing. Always turn the tempe-

rature control to „0“ after use and remove the mains

plug (the control lamp in the handle goes o ).

• Turn the switch (4) on the base o .

• Remove the mains plug from the socket.

• Empty the water tank.

• Allow the device to cool down before you put it

away.

Cleaning

AVVISO:

• Always remove the mains lead before cleaning!

• Wait until the machine has cooled down complete-

ly.

• Under no circumstances should you immerse the

device in water for cleaning purposes. Otherwise

this might result in an electric shock or  re.

CAUTION:

• Do not use a wire brush or any abrasive items.

• Do not use any acidic or abrasive detergents.

• Clean the casing with a slightly damp cloth.

• Clean the sole plate and the rest with a slightly damp

cloth.

• Any residual water can remain in the water tank, but

should be poured out if it has been in the tank for a

prolonged period.

05-DBS 5533.indd 3105-DBS 5533.indd 31 09.02.2009 11:36:58 Uhr09.02.2009 11:36:58 Uhr

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG DBS 5533 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG DBS 5533 Manual

Product: